LAPORAN

PRATIKUM JARINGAN

“Konfigurasi VLAN dan VTP”

ARYA AULIA

1101082007

Teknik Kompurer 2a

TEKNOLOGI INFORMASI

POLITEKNIK NEGERI PADANG

2013

Konfigurasi VLAN dan VTP

Ini adalah konfigurasi dasar VLAN dan Virtual Trunking Protocol (VTP).

Pada posting kali i ni akan dibahas :

1. Konfigurasi Switch sebagai VTP Server

2. Mengkoneksikan 4 switch lainnya dan menkonfigurasinya sebaga VTP client. Semua link

antar Switch harus dikonfigurasi sebagai trunk link

3. Konfigurasi VTP domain dengan nama MYDOMAIN dan VTP password dengan cisco

4. Konfigurasi VLAN 10 dengan nama “MAHASISWA” dan VLAN 50 dengan nama

„SERVER”

5. Uji propagasi pada semua switch dari domain VTP.

Kita mulai konfigurasi pada Switch yang akan dijadikan server!

Switch VTP-Server

Masuk ke mode priviledge : VTP-SERVER>enable

Global configuration VTP-SERVER#conf t

Enter configuration commands, one per line. End with CNTL/Z.

VTP-Server(config)#line con 0

VTP-Server(config-line)#password cisco

VTP-Server(config-line)#login

VTP-Server(config-line)#exit

VTP-Server(config)#line vty 0 4

VTP-Server(config-line)#password cisco

VTP-Server(config-line)#login

VTP-Server(config-line)#exit

VTP-Server(config)#enable secret cisco

Konfigurasi VTP VTP-Server(config)#vtp mode server

Device mode already VTP SERVER.

VTP-Server(config)#vtp domain MYDOMAIN

Changing VTP domain name from NULL to MYDOMAIN

VTP-Server(config)#vtp password cisco

Setting device VLAN database password to cisco

Konfigurasi VLAN VTP-Server(config)#vlan 10

VTP-Server(config-vlan)#name MAHASISWA

VTP-Server(config-vlan)#exit

VTP-Server(config)#vlan 50

VTP-Server(config-vlan)#name SERVER

VTP-Server(config-vlan)#exit

VTP-Server(config)#interface vlan1

VTP-Server(config-if)#ip ?

address Set the IP address of an interface

helper-address Specify a destination address for UDP

broadcasts

VTP-Server(config-if)#ip address 192.168.1.1 255.255.255.0

VTP-Server(config-if)#no shutdown

VTP-Server(config-if)#exit

Konfigurasi Trunk Link VTP-SERVER(config)#int gi1/1

VTP-SERVER(config-if)#swi

VTP-SERVER(config-if)#switchport mo

VTP-SERVER(config-if)#switchport mode tru

VTP-SERVER(config-if)#switchport mode trunk

%LINEPROTO-5-UPDOWN: Line protocol on Interface

GigabitEthernet1/1, changed state to down

%LINEPROTO-5-UPDOWN: Line protocol on Interface

GigabitEthernet1/1, changed state to up

VTP-SERVER(config-if)#exit

VTP-SERVER(config)#int gi1/2

VTP-SERVER(config-if)#swit

VTP-SERVER(config-if)#switchport mode trunk

%LINEPROTO-5-UPDOWN: Line protocol on Interface

GigabitEthernet1/2, changed state to down

%LINEPROTO-5-UPDOWN: Line protocol on Interface

GigabitEthernet1/2, changed state to up

VTP-SERVER(config-if)#exit

VTP-SERVER(config)#^Z

VTP-SERVER#

%SYS-5-CONFIG_I: Configured from console by console

VTP-SERVER#

Simpan Konfigurasi VTP-Server#copy run st

Destination filename [startup-config]?

Building configuration...

[OK]

VTP-Server#

Switch VTP-Client1

Switch>en

Switch#configure terminal

Enter configuration commands, one per line. End with CNTL/Z.

Switch(config)#hostname VTP-Client1

VTP-Client1(config)#line con 0

VTP-Client1(config-line)#pass cisco

VTP-Client1(config-line)#login

VTP-Client1(config-line)#line vty 0 4

VTP-Client1(config-line)#pass cisco

VTP-Client1(config-line)#login

VTP-Client1(config-line)#

VTP-Client1(config-line)#exit

VTP-Client1(config)#enable secret cisco

VTP-Client1(config)#

VTP-Client1(config)#vtp mode client

Setting device to VTP CLIENT mode.

VTP-Client1(config)#vtp domain MYDOMAIN

Domain name already set to MYDOMAIN.

VTP-Client1(config)#vtp password cisco

Setting device VLAN database password to cisco

VTP-Client1(config)#interface vlan 1

VTP-Client1(config-if)#ip add 192.168.1.2 255.255.255.0

VTP-Client1(config-if)#no sh

%LINK-5-CHANGED: Interface Vlan1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed

state to up

VTP-Client1(config-if)#exit

VTP-Client1(config)#int gi1/1

VTP-Client1(config-if)#switch mode trunk

VTP-Client1(config-if)#exit

VTP-Client1(config)#int gi1/2

VTP-Client1(config-if)#switch mode trunk

%LINEPROTO-5-UPDOWN: Line protocol on Interface

GigabitEthernet1/2, changed state to down

%LINEPROTO-5-UPDOWN: Line protocol on Interface

GigabitEthernet1/2, changed state to up

VTP-Client1(config-if)#exit

VTP-Client1(config)#^Z

VTP-Client1#

%SYS-5-CONFIG_I: Configured from console by console

VTP-Client1#copy run st

Destination filename [startup-config]?

Building configuration...

[OK]

VTP-Client1#

Switch VTP-Client2

Lakukan konfigurasi seperti pada Switch VTP-Client1, akan tetapai ip address vlan 1 adalan

192.168.1.3 255.255.255.0

VTP-Client2(config)#interface vlan 1

VTP-Client2(config-if)#ip add 192.168.1.3 255.255.255.0

VTP-Client2(config-if)#no sh

Switch VTP-Client3

Lakukan konfigurasi seperti pada Switch VTP-Client1, akan tetapai ip address vlan 1 adalan

192.168.1.4 255.255.255.0

VTP-Client3(config)#interface vlan 1

VTP-Client3(config-if)#ip add 192.168.1.4 255.255.255.0

VTP-Client3(config-if)#no sh

Switch VTP-Client4

Lakukan konfigurasi seperti pada Switch VTP-Client1, akan tetapai ip address vlan 1 adalan

192.168.1.5 255.255.255.0

VTP-Client2(config)#interface vlan 1

VTP-Client2(config-if)#ip add 192.168.1.5 255.255.255.0

VTP-Client2(config-if)#no sh