Modul Perfect Score SBP Fizik SPM 2012

78
Physics Perfect Score SBP 2012 SBP 2012 PHYSICS SEKOLAH BERASRAMA PENUH 2012 PERFECT SCORE MODULE NAME :................................................................... CLASS/SCHOOL:.................................................

description

Modul Perfect Score SBP Fizik SPM 2012

Transcript of Modul Perfect Score SBP Fizik SPM 2012

Page 1: Modul Perfect Score SBP Fizik SPM 2012

1

Physics Perfect Score SBP 2012

SBP 2012

PHYSICS

SEKOLAH

BERASRAMA PENUH

2012

PERFECT SCORE MODULE

NAME :...................................................................

CLASS/SCHOOL:.................................................

Page 2: Modul Perfect Score SBP Fizik SPM 2012

2

Physics Perfect Score SBP 2012

SBP 2012

PHYSICS PERFECT SCORE 2012 PANELS

NOR SAIDAH BT CHE HASSAN (Ketua Penggubal)

Kolej Tunku Kurshiah

JENNYTA BT NOORBI

SMS Tuanku Munawir

JAMILAH YUSOF

Sekolah Seri Puteri

HASLINA BT ISMAIL

SMS Hulu Selangor

KAMARIAH BT MOHD ARSYAD

The Malay College of Kuala Kangsar

JAMALUDIN BIN ABD GHANI

SBPI Batu Rakit

HJH NOR SHIDAH HJ MANSOR

SMS Tengku Mahmud

SURIYATI YUSOFF

SMS Muzaffar Shah

TAN LEE FAH

SMS Miri

ZULAIFAH ZINUDDIN

Sekolah Tuanku Abdul Rahman

Page 3: Modul Perfect Score SBP Fizik SPM 2012

3

Physics Perfect Score SBP 2012

SBP 2012

TABLE OF CONTENT

SECTION CONSTRUCT/CONTENT Page

Section I Physics Concept / Rules / Principles /Laws 4

Section II Examples of Common Mistakes And

Misconceptions 14

Section III Construct: Understanding 19

Section IV Construct Decision Making 26

Section V C Construct onceptualisation 40

Section VI Construct (Qualitative) 53

Section VII Problem Solving (Quantitative) 58

Section VIII A Paper 3 Section A 63

Section VIII B Paper 3 Section B 71

Page 4: Modul Perfect Score SBP Fizik SPM 2012

4

Physics Perfect Score SBP 2012

SBP 2012

-PHYSICS CONCEPT AND DEFINITION

Chapter 1: Introduction to Physics

What is.. Definition

1 Base Quantities Base quantities are quantities that cannot be defined in terms

of other base quantities

2. Derived Quantities

Derived quantities are quantities that are obtained by

combining base quantities by multiplication, derivition or both

operations

3. Scalar Quantities Scalar quantities are quantities that have only magnitude

4. Vector Quantities Vector quantities are quantities that have both magnitude

and direction

5. Consistency

The consistency of of a measuring instrument is its ability

register the same reading when a measurement is made

repeatedly

6. Accuracy Accuracy is the degree of how close a measurement is to the

actual vaue

7. Sensitivity Sensitivity of an instrument is its ability to detect a small

change in the quantity to be measured

Chapter 2: Force And Motion

What is.. Definition

1. Speed Speed is the rate of change of distance

2. Velocity Velocity is the rate of change of displacement

3. Acceleration Acceleration is the rate of change of change/increase in

velocity

4. Deceleration Deceleration is the rate of decrease in velocity

5. Inertia The inertia of an object is the tendency of the object to remain

its state of rest or uniform motion in a straight line

6. Newton’s First Law of

Motion / Law of Inertia

Newton’s First Law of Motion states that every object continues

in its state of rest or uniform speed in a straight line unless acted

upon by an external force

7. Linear momentum Linear momentum is the product of mass and velocity

8. Principle of Conservation

of Momentum

Principle of Conservation of Momentum states that the total

momentum of a system remains unchanged if no external

force acts on the system.

9. Force Force is defined as anything that changes the state of rest or

motion of an object moving in a straight line

Page 5: Modul Perfect Score SBP Fizik SPM 2012

5

Physics Perfect Score SBP 2012

SBP 2012

What is.. Definition

10. Newton’s Second Law

The acceleration of a body ,a, is directly proportional to the

net force acting on it, F , and inversely proportional to its mass,

m

11. Impulse Impulse is defined as the change in momentum

12. Impulsive Force Impulsive force is defined as the rate of change of momentum

13. Weight / Force of

Gravity / Gravitational

Force

Pulled force towards the centre of the earth

14. Free-Fall A free-falling object is an object falling under the force of

gravity only

15. Gravitational

Acceleration The acceleration of objects due to gravity // falling free

16. Gravitational Field The gravitational field is the region around the earth in which

an object experience a force due to gravitational attraction

17. Resultant Force /

Net Force

Resultant force is a single force that represents the combined

effect of two or more forces in magnitude and direction

18. Unbalanced Forces /

When the forces acting on an object is not balanced, there

must be a net force/unbalanced/resultant force acting on it

Unbalanced forces produce an acceleration to the object

19. Forces in Equilibrium /

Balanced Forces

The object is said to be in a state of equilibrium when the

resulting force acting on the object is zero ( no net force acting

upon it)

When the equilibrium is reached, then the object is in two

states, that is

(i) remains stationary (if the object is stationary)

(ii) moves at a constant velocity ( if the object is moving) /

zero acceleration

20. Newton’s Third Law of

Motion

Newton’s third law of motion states that, To every action there

is an equal but opposite direction

21. Work

Work is defined as the product of the applied force ,F on the

object and its displacement, s in the direction of the applied

force

22. Energy Energy is the ability to do work

(Work done is equal to the amount of energy transferred

23. Gravitational Potential

Energy

The Gravitational potential energy of an object is the energy

stored in the object due to its position in a force field

24. Kinetic Energy Kinetic energy is the energy possessed by an object due to its

motion

25. Principle of Conservation

of Energy Principle of Conservation of Energy states that

Page 6: Modul Perfect Score SBP Fizik SPM 2012

6

Physics Perfect Score SBP 2012

SBP 2012

What is.. Definition

26. Power Power is the amount of work done per second

27. Efficiency Efficiency of a device is the percentage of the energy input

that is transferred into useful energy

28. Elasticity

Elasticity is the property of a substance which enables it to

return to original shape after an applied external force is

removed

29. Elastic Limit

Elastic limit of a spring is defined as the maximum force that

can be applied to a spring such that the spring will be able to

restored to its original length when the force is removed

30. Hooke’s Law

Hooke’s Law states that the extension of a spring is directly

proportional to the applied force provided that the elastic limit

is not exceeded

31. Spring Constant /

Force Constant

A spring constant of a spring is the force that is required to

produce one unit of extension of the spring

(measure of the stiffness of the spring)

32. Elastic Potential Energy Elastic Potential Energy is the energy stored in a spring when it is

extended or compressed

Chapter 3: Force and Pressure

What is.. Definition

1. Pressure Pressure is defined as the force acting normally on a unit of

surface area

2. Atmospheric Pressure The Atmospheric pressure is caused by the the weight of the air

on the Earth’s surface

3. Gas Pressure Gas pressure is the force per unit area exerted by the gas

molecules as they collide with the walls of their container

4. Pascal’s Principle

Pascal’s principle states that when pressure is applied to an

enclosed fluid, the pressure will be transmitted equally

throughout the whole enclosed fluid

5. Bouyant Force Bouyant Force is an upward force resulting from an object being

wholly or partially immersed in a fluid

6. Archimedes’ Principle

Archimedes’ Principle states that, “ When an object is immersed

in a fluid, the buoyant force on the object is equal in size to the

weight of fluid displaced by the object

7. Bernoulli’s Principle Bernoulli’s principlestatesthat the pressure of a moving liquid

decreases as the speed of the fluid increases and vice versa

Page 7: Modul Perfect Score SBP Fizik SPM 2012

7

Physics Perfect Score SBP 2012

SBP 2012

Chapter 4: Heat

What is.. Definition

1. Temperature Temperature is the degree of hotness of an object /

Amount of kinetic energy in an object

2. Heat Heat is the energy tranferred from hot to cold object

3. Thermal Equilibrium

Two objects are said to be in thermal equilibrium when;

i) The rates of heat tansfer between the objects are

equal (net flow of heat between the two objects is

zero)

ii) The objects have the same temperature

4. Thermometric Property

Thermometric Property is the physical property of a substance

which is sensitive and varies linearly with changes in temperature

of the material

5. Ice Point (Lower fixed

pont) Ice point is the temperature of pure melting ice

6. Steam Point (Upper

fixed point)

Steam point is the temperature of steam from water that is

boiling under standard atmospheric pressure

7. Heat Capacity Heat capacity of a body is the amount of heat that must be

supplied to increase its temperature by 1 oC

8. Specific Heat

Capacity

Specific Heat Capacity of a substance is the amount of heat

that must be supplied to increase the temperature by 1 oC for a

mass of 1 kg of the substance

9. Latent Heat Latent heat is the heat absorbed or heat released at a constant

temperature during a change of phase

10. Specific Latent Heat

Specific Latent Heat of a substance is the amount of heat

required to change the phase of 1 kg of the substance at a

constant temperature

11. Spesific Latent Heat of

Fusion

Spesific Latent Heat of Fusion is the amount of heat required to

change the phase of 1 kg of the substance from solid to liquid

phase at a constant temperature

12. Spesific Latent Heat of

Vaporisation

Spesific Latent Heat of Fusion is the amount of heat required to

change the phase of 1 kg of the substance from liquid to

gaseous phase at a constant temperature

13. Boyle’s Law

Boyle’s Law states that for a fixed mass of gas, the pressure of

the gas is inversely proportional to its volume when the

temperature is kept constant

14. Charles’ Law

Charles’ Law states that for a fixed mass of gas, the volume of

the gas is directly proportional to its absolute temperature when

its pressure is kept constant

15. Pressure Law

Pressure Law states that for a fixed mass of gas, the pressure of

the gas is directly proportional to its absolutev temperature

when the volume is kept constant

Page 8: Modul Perfect Score SBP Fizik SPM 2012

8

Physics Perfect Score SBP 2012

SBP 2012

Chapter 5: Light

What is.. Definition

1. Law of Reflection

AO :Incident ray

ON :Normal

OB :Reflected ray

i :Angle of

incidence

r :Angle of

reflection

i. The incident ray, the reflected ray and the normal all lie in

the same plane

ii. The anle of incidence i, is equal to the angle of reflection, r

Reflection by a concave

mirror

Parallel rays that strike the surface of a concave mirror will be

reflected and converge at the focal point, F outside the mirror

Centre of curvature, C of a curved mirror is the centre of the

sphere of the mirror

Radius of curvature. R is the distance between the the centre of

curvature, C and the pole of the mirror

Focal point is the point where parallel rays that strike the surface

of a concave mirror will be reflected and converge at the focal

point

2. Refraction of light

Refraction of light is a light phenomenon which occurs when

light passes through two materials of different optical densities,

will change direction at the boundary between them.

3. Refractive Index Refractive Index, n of the medium is defined as the ratio of the

speed of light in vacuum to the speed if light in the medium

4. Law of Refraction and

Snell’s Law

i. The incident ray, the refracted ray and the normal all lie in

the same plane

ii. The value of sin i is a constant (Snell’s Law)

sin r

5. Critical Angle Critical angle is the angle of incidence in an optically more

dense medium which results in angle of refraction of 90o in an

optically less dense.

6. Total Internal

Reflection

The Internal Reflection of light is the phenomenon when the

angle of incidence is greater than the critical angle and the light

not refracted anymore but internally reflected

The conditions for the occurrence of total internal reflection.

(1) The light ray must be travel from an optically denser

medium to less dense medium.

(2) The angle of incidence must be greater than the

critical angle.

Page 9: Modul Perfect Score SBP Fizik SPM 2012

9

Physics Perfect Score SBP 2012

SBP 2012

Chapter 6: Waves

What is.. Definition

1. Waves Waves are carriers of energy. They transfer energy from one

location to another

2. Longitudinal Wave

Longitudinal Wave is a wave in which the vibration of particles in

the medium is parallel to the direction of the propagation of the

wave

3. Transverse Wave

Transverse Wave is a wave in which the vibration of particles in

the medium is perpendicular to the direction of propagation of

the wave

4. Wavefront In waves, lines joining all the points of the same phase

5. Wavelength Wavelength of a wave is the distance between two adjacent

points of the same phase on a wave

6. Amplitude Amplitude is the maximum displacement from its equilibrium

position

7. Frequency Frequency of a wave is the number of waves produced by a

source in one second

8. Wave speed The speed of the wave is the measurement of how fast a crest is

moving from its fixed point

9. Period The period of a wave is the time taken for an oscillation to

complete one cycle

10. Forced Oscillation Forced Oscillation is the external force supplies energy to the

system

11. Natural Frequency Natural Frequency is the frequency of a system which oscillate

freely without the action of an external force

12. Resonance

Resonance occurs when a system is made to oscillate at a

frequency equivalent to its natural frequency by an external

force

13. Diffraction

Diffraction of waves is the spreading of waves around corners

and edges as waves pass through an opening or around an

obstacle along their paths

14. Coherent Waves Coherent Waves are waves that have same frequency and

wavelength and in phase

15. Monochromatic Light Monochromatic Light is light with one colour/wavelength

16. Principle of

Superposition of

Waves

Principle of Superposition states that when two waves interfered,

the resulting displacement of the medium at any point is the

algebraic sum of the displacements of the individual waves

17. Constructive

interference

Constructive interference occurs when a crest meets acrest and

when a trough meets a trough

Page 10: Modul Perfect Score SBP Fizik SPM 2012

10

Physics Perfect Score SBP 2012

SBP 2012

What is.. Definition

18. Destructive

interference

Destructive interference occurs when crests suoerposed with

troughs

19. Antinodal lines Antinodal lines are lines joining places of constructive

interference

20. Nodal lines Nodal lines are line joining the places of destructive interference

Chapter 7: Electricity

What is.. Definition

1. Electric Field Electric field is a region around a charged object which any

other charged body experience a force

2. Potential Difference

Potential Difference, V between two points in a circuit is defined

as the amount of work done when a coulomb of charge passes

from one point to the other point

3. Ohm’s Law

Ohm’s Law states that the current that passes through an ohmic

conductor is directly proportional to the potential difference

applied accross it if the temperature and other physical

conditions are constant

4. Resistance Resistance, R of a conductor is the ratio of the potential

difference, V to the current, I

5. Electromotive Force

(e.m.f)

Electromotive Force (e.m.f) is defined as the work done by the

source to move a coulomb of charge around a complete circuit

6. Internal Resistance The internal resistance ,r is the resistance within a cell due to its

electrolyte and electrodes or source of electricity.

Chapter 8: Electromagnetism

What is.. Definition

1. Ferromagnetic

materials

Ferromagnetic materials are the materials attracted to the

magnet. The examples of the ferromagnetic materials such as

iron, nickel and cobalt

2. Electromagnet

An electromagnet is a device in which magnetism is produced

by an electric current.

An electromagnet acts as a temporary magnet

3. Magnetic field

A magnetic field is a region in which a magnetic material

experiences a force as the result of the present of a magnet or

a electromagnet

Page 11: Modul Perfect Score SBP Fizik SPM 2012

11

Physics Perfect Score SBP 2012

SBP 2012

What is.. Definition

4. The right -hand grip

rule.

If a solenoid carrying a current is gripped with the right hand

and with the thumb pointing along the solenoid so that the

fingers curling round the solenoid in the direction of the current

and the thumb then points towards the north pole.

5. Fleming’s Left-hand

Rule.

Fleming’s Left-hand Rule.

Fleming’s Left-hand Rule states” If the thumb, first finger

(forefinger)and second finger of the left hand are held at right

angles to each other, then if the first finger (forefinger)represents

the direction of the magnetic field and the second represents

the direction of the current, then the thumb will represents the

direction of the motion”

6. Catapult Field

(Resultant field)

Catapult field are the combinations field between

(a) the magnetic field produced by the current and

magnetic field of the permanent magnet occurred.

Or

(b) the magnetic field produced by two current –carrying

conductors are placed close to each other

7. Electromagnetic

induction

Electromagnetic induction is the production of induced current

or induced e.m.f. without using the power supplies but using the

relative motion between a conductor or a magnet

8. Faraday’s law

Faraday’s law state that “ The magnitude of the induced

current or induced e.m.f. is directly proportional to the rate of

change of magnetic flux linkage with the solenoid or the rate at

which a conductor cuts through the magnetic flux.”

9. Lenz’s law

Lenz’s law state that” The direction of an induced current

always flows in such as a direction so to oppose the change

which is causing it.”

Page 12: Modul Perfect Score SBP Fizik SPM 2012

12

Physics Perfect Score SBP 2012

SBP 2012

What is.. Definition

10. Fleming’s Right-hand

rule

To determine the direction of the induced current in the

dynamo – Fleming’s Right-hand rule

Fleming’s Right-hand Rule states” If the thumb, first finger

(forefinger)and second finger of the right hand are held at right

angles to each other, then if the first finger (forefinger)represents

the direction of the magnetic field and the thumb represents

the direction of the motion of the conductor , then the

second finger will represents the direction of the induced

current ”

Page 13: Modul Perfect Score SBP Fizik SPM 2012

13

Physics Perfect Score SBP 2012

SBP 2012

Chapter 9: Electronics

What is.. Definition

1. Thermionic Emission

The emission of electrons from the surface of a heated metal or

heated metal cathode.

The thermionic emission is a bit like electrons being evaporated

off from the hot wire

2. Cathode Ray Cathode ray is a narrow beam of a fast electrons moving in a

vacuum

3. Semiconductor

Materials

Semiconductors are materials which conduct electricity better

than insulator, but no so well as ordinary conductors

4. Doping Doping is a process of adding a small amount of impurities into

the pure crystal of semiconductor (intrinsic semiconductor)

5. Rectifier

A rectifier converts alternating current(a.c.) into direct

current(d.c).

The process of converting a.c. to d.c. is called rectification

6. Transistor

A transistor is a semiconductor device capable of amplification

in addition to rectification.

7. Logic Gate An electronic circuit with a single output and one or more inputs

Chapter 10: Radioactivity

What is.. Definition

1. Radioisotope Radioisotopes are unstable isotopes which decay and give out

radioactive emissions

2. Radioactivity

Radioactivity is the spontaneous disintegration of an unstable

nucleus into a more stable nucleus accompanied by the

emission of energetic particles (radioactive rays) or photons

3. - particles : Helium nucleus or He4

2

4. - particles : Fast moving electrons or e0

1

5. -rays Electromagnetic waves

6. The half-life The half-life of a radioactive material is the time taken for the

activity of radioactive fall to half its original activity

7. Nuclear fission

Nuclear fission is the splitting of a heavy nucleus into two lighter

nuclei, which subsequently emit either two or three neutrons and

release of large amounts of energy

8. Nuclear fusion Nuclear fusion is the combining of two lighter nuclei to form a

heavier nucleus with the release of large amount of energy.

Page 14: Modul Perfect Score SBP Fizik SPM 2012

14

Physics Perfect Score SBP 2012

SBP 2012

SECTION II - COMMON MISTAKES AND MISCONCEPTIONS

A. Common Mistakes

1. Problem Solving (Quantitative) –the answer given:

i. FRACTION FORM

ii. without UNIT

2. Careless mistakes:

Example: Convert minute into hour - 30 minutes = 30 x 60 = 1800 hours

3. Conceptual question:

i. Giving the reason:

E.g. : The horizontal distance of the water spurting out in Diagram (b) is greater

because.....

ii. Giving the value when comparing two situations:

E.g. The boiling points of water is 100oC whereas the boiling point of

methylated spirit is 80oC

4. Understanding Question - Not systematic in explanation

5. Explanation without diagram / symbol / formula / graph.

6. Use the reason given in the question

7. Light topic; Draw the ray diagram without “arrow”

8. Cannot distinguish between Physical Quantity, Physics Instrument and Physics Unit

Examples:

Physical Quantity Physical quantity measured Physics Unit and symbol

Stop watch

voltmeter

thermometer

Bourdon gauge

Ammeter

9. Wrong Physics Term / Definition / Concept (Base on SBP Physics Trial Exams)

Examples:

Terms Common Mistake Correct Answer

a

[The type of energy

when the object is at P]

Potential energy

................................ Potential

Energy

Page 15: Modul Perfect Score SBP Fizik SPM 2012

15

Physics Perfect Score SBP 2012

SBP 2012

Terms Common Mistake Correct Answer

b Pressure

Force acting on surface

area

Force/area

A product of depth, density

and gravitational

acceleration

.................................. force acting

on ...................... of surface area

c Pascal’s principle In a close container, force is

transmitted equally

In a close container......................

.........................................................

d Latent heat of

vaporization Heat absorbed to change

by 1oC

Heat absorbed to change

.................... of liquid to gas

without ............................................

.........................................................

e Temperature

Transfer from hot body to

cold body

f

[Physics phenomena in

a prism]

Reflection ....................................................

g Critical angle

Critical angle is when the

refracted angle is 90o

Critical angle is the incident

angle when the reflected

angle is 90o

Critical angle is the ................

.............. in ............................r

medium which produces when

the ................................. angle in

................................ medium is

.........................

h Virtual image The image that formed

behind the lens

The image that ..............................

........................................................

i Monochromatic light A colour of one light The light that .................................

.........................................................

j Amplitude Maximum point of the

highest displacement

…………………………..

....................................... of any

particle/oscillating system from

its …………………………………...

Page 16: Modul Perfect Score SBP Fizik SPM 2012

16

Physics Perfect Score SBP 2012

SBP 2012

Terms Common Mistake Correct Answer

k Period One complete oscillation

The …………………………. for

any particle to make ………

………………….oscillation

l Specification:

240 V, 1000 W

1000 W of energy is supplied

when the power supplied is

240 V.

...................................................

..................................................

when connected to a .............

.......................... of .....................

..........................

j electromagnet

When the current flow

through magnet

Is a combination of electric

and magnetic field

A .............................. which can

produce .......................................

when ..............................................

.........................................................

k Beta particles Negative charge ................................ electron

Page 17: Modul Perfect Score SBP Fizik SPM 2012

17

Physics Perfect Score SBP 2012

SBP 2012

B. Misconceptians

Examples:

Num Misconceptions Correction

1 Oil is used in hydraulic jack because it has

higher boiling point

2

Snell’s law state that:

The sine of incident

angle =

Refractive

index The sine of refracted

angle

3

Container A Container B

The force exerted at X > the force exerted at Y

because smaller surface area (P = F /A)

To increase the efficiency of ac/dc

GENERATOR:

- Use more number of turns to produce

stronger magnetic field

The ship can float in sea water because the

buoyant force is bigger than the weight of the

ship

water

Page 18: Modul Perfect Score SBP Fizik SPM 2012

18

Physics Perfect Score SBP 2012

SBP 2012

C. Paper 3

1. Data Tabulation

Title - no unit

Content- not consistent

Example:

Common Mistake Correct Answer

Electric Current Voltage

0.1 0.5

0.12 1

0.14 1.5

2. Graph:

Label - x-axis & y-axis : no unit

Scale - Not uniform, odd

Plotting (x @ )- too small or too big

Line - not smooth, not balance

Size - small [< (8 cm x 8 cm)]

3. Gradient of the graph

Triangle - small [ < (8 cm x 8 cm)]

Final answer - no unit,

Written in fraction

4. Calculation

Final answer - no unit

written in fraction

5. Procedure

Repeat the experiment three times

Should state:

What:……………………………………………………………………………………………..……..

How : ……………………………………………………………………………………………..…….

6. Precaution

“Avoid parallax error”

Should state: What: …………………………………………………………………………………

How : …………………………………………………………………………………

Page 19: Modul Perfect Score SBP Fizik SPM 2012

19

Physics Perfect Score SBP 2012

SBP 2012

SECTION III– UNDERSTANDING - (Paper 2 Section B and C )

Question 1 [ Introduction to Physics ]

Explain the meaning of consistency and accuracy of a measuring instrument by using suitable examples

[ 4 marks ]

Question 2 [Forces and Motion]

Using the principle of conservation of momentum, explain the working principle of the rocket.

[4 marks]

Question 3 [Forces and Motion

Spring is widely used in suspension system of vehicles such as car and motorcycle. This is because of the

elasticity of the spring. Diagram below shows how a spring is used in suspension system of a car.

(i) What is meant by elasticity?

(ii) Explain how the forces between the molecules caused the elasticity when the spring is

compressed and stretched.

[4 marks]

Question 4 [Forces and Motion]

Diagram 4 shows a hovercraft starts from rest and accelerates until it achieves constant velocity after a

few seconds.

Diagram 4

(i) Sketch a velocity-time graph to show the motion of hovercraft.

(ii) Explain why the hovercraft moves with constant velocity in terms of the force acting on it

[4 marks]

Question 5 [Forces and Pressure]

Explain why the atmospheric pressure at higher altitude is lower compared to places at lower altitude.

[4 marks]

Page 20: Modul Perfect Score SBP Fizik SPM 2012

20

Physics Perfect Score SBP 2012

SBP 2012

Question 6 [Forces and Pressure]

Diagram shows a suction pump being used to lift a mirror that measured 1.5 m X 0.5 m X 0.01m . The

density of the mirror is 2.5 X 10 3 kg m-3 . The pump obeys atmospheric pressure principle to let the suction

pump stick onto surface of mirror.

Diagram 6

Explain how the suction pump can lift the mirror with the aid of atmospheric pressure.

[4 marks]

Question 7 [Forces and Pressure]

Diagram

(i) State Archimedes’ principle.

. [1 mark]

(ii) Explain why a weather balloon that is rising up in the air will stop at certain altitude

[4 marks]

Page 21: Modul Perfect Score SBP Fizik SPM 2012

21

Physics Perfect Score SBP 2012

SBP 2012

Question 8 [Forces and Pressure]

(a) Diagram shows a hydrometer.

Diagram

A hydrometer is used to measure density of liquid. Explain how a hydrometer functions.

[4 marks]

Question 9 [Heat]

(i) What is the meaning of thermal equilibrium? [1mark]

(ii) Explain, in terms of thermal equilibrium, how a thermometer which is placed into the boiling water reads

at the temperature of 100 ˚C.

[4marks]

Question 10 [Heat]

Using kinetic theory of gaseous, explain how the pressure increase when the temperature increase.

[4 marks]

Question 11 [Heat]

Diagram shows the phenomenon of sea breeze.

Diagram

Using the concept of specific heat capacity, explain how the phenomenon of sea breeze occurs.

[4 marks]

Page 22: Modul Perfect Score SBP Fizik SPM 2012

22

Physics Perfect Score SBP 2012

SBP 2012

Question 12 [Light]

Diagram shows the “superior mirage “ which occurs over cold water surface and snow.

Using physics concepts, explain why the observer can only see the image of the ship.

[4 marks]

Question 13 [Light]

Explain why a piece of paper burns when placed under a convex lens aimed towards hot sun rays.

[4 marks]

Question 14 [Waves]

Sonar technique can be used to determine the distance between two positions. Ultrasonic wave is used

in this technique.

(i) What is sonar?

[ 1 mark ]

(ii) Explain why using ultrasonic wave is better than just ordinary sound waves.

[ 2 marks ]

(iii) A marine researcher wants to use ultrasonic sound to determine the depth of the ocean bed.

Explain how he can do so.

[ 4 marks ]

Question 15 [Waves]

Explain why strong double-glazed glass is used as walls of the observation tower in an airport.

[4 marks]

Cool air

Warm air

ship

Image of ship

Page 23: Modul Perfect Score SBP Fizik SPM 2012

23

Physics Perfect Score SBP 2012

SBP 2012

Question 17 [Electricity]

Explain the advantages of parallel circuit in a house wiring system

[4 marks]

Question 18 [Electricity]

Explain why the bulb connected to two dry cells lights up brighter than one bulb connected to one dry

cell.

[4 marks]

Question 19 [Electromagnetism]

Explain what happens to magnet P and magnet Q when the switch is on.

[4 marks]

Question 20 [Electromagnetism]

Diagram shows a simple direct current electric motor.

Using the concept of the magnetic effect of an electric current, explain with the aid of diagrams how

forces are produced on a wire in the coil, as shown in the diagram above.

Question 21 [Electromagnetism]

Diagram shows a circuit breaker. Explain how the circuit breaker works.

[ 4marks]

Page 24: Modul Perfect Score SBP Fizik SPM 2012

24

Physics Perfect Score SBP 2012

SBP 2012

Question 22 [Electromagnetism]

(i) What is meant by ideal transformer?

[ 1 mark ]

(ii) Explain the working principle of a transformer.

[ 4 marks ]

Question 23 [Electromagnetism]

Diagram shows the model of an electricity transmission system.

Most of the electric energy that we are using come from hydroelectric and thermal power station. This

power station is connected to each other using cable to transmit electric energy to industries, office,

school and house. This system called National grid network.

State the form of energy transfer at hydroelectric power station.

Explain the importance of National grid network system in electricity transmission to consumers.

Power stationn

Industry at 8 V a.c

House at 6 V a.c

Transmission wire at 24 V a.c

Page 25: Modul Perfect Score SBP Fizik SPM 2012

25

Physics Perfect Score SBP 2012

SBP 2012

Question 24 [Electronic]

Diagram shows a Cathode-Ray Oscilloscope.

Explain how the Cathode-Ray Oscilloscope can be used to measure the potential difference of a dry cell.

[ 4marks ]

Question 25 [Radioactivity]

Radioisotope Strontium-90 is used to measure the thickness of paper in a paper industry .Explain how

Strontium-90 is used to measure the thickness piece of paper?

[4 marks]

Question 26 [Radioactivity]

Radioisotopes can be used as tracers to detect leaks from pipes underground. Diagram 12.1 shows a leak

that occurred in an underground water pipe.

(a) What is meant by radioisotopes?

[ 1 mark ]

(b) With the aid of diagram, explain how radioisotopes can be used to detect the location of the

leakage as shown in Diagram.

[ 3 marks ]

Question 27 [Radioactivity]

The following equation shows a fission reaction of Uranium-235.

Nuclear fission produces a chain reaction.

Describe how the chain reaction occurs in a nuclear fission of an atom of Uranium- 235.

[4 marks]

Page 26: Modul Perfect Score SBP Fizik SPM 2012

26

Physics Perfect Score SBP 2012

SBP 2012

SECTION IV – DECISION MAKING (Paper 2 Section A – Question 8; Section C )

Question 1 [Force and Pressure]

Table 1 shows the characteristics of four structures of ship P, Q, R, and S.

Structure of

ships Shape

Strength Of the

metal used

Ship Base Cross

section area

Volume of the air

space in the ship

U

Streamlined

High

Wide

High

V

Oval

Low

Wide

High

W

Circle

High

Small

Low

X

Streamlined

Low

Small

Low

Table 1

As a researcher in a ship manufacturing company, you are assigned to study the structure used to make

the ship to support heavy cargoes.

You are given four choices of the structures P, Q, R and S. The table above shows the structures of the ship.

Explain the suitable characteristics of the structure to be used to make the ship.

Determine the most suitable structure to be used to make the ship to support heavy cargoes.

Give reasons for your choice.

[10 marks]

Question 2 [Force and Pressure]

At National Water Rocket competition, the winner is supposed to design a water rocket which can be

launched to a higher altitude, further distance and take the longest time to land.

You are asked to investigate the characteristics of the water rockets in thediagram 11.2 and determine

the best rocket to use in the competition. Give reasons for your choice.

P

Q

Page 27: Modul Perfect Score SBP Fizik SPM 2012

27

Physics Perfect Score SBP 2012

SBP 2012

R

S

T

[10 marks]

Question 3 [Force and Pressure]

Diagram 3 shows four racing motorcycles, P, Q, R and S, with different specifications. You are required

to determine the most suitable motorcycle to move fast and safe when racing.

Study the specifications of all the four motorcycles from the following aspects:

Explain the suitability of the aspects.

Justify your choice.

Racing bike A

Type of brake : without ABS

Mass : 205.0 kg

Page 28: Modul Perfect Score SBP Fizik SPM 2012

28

Physics Perfect Score SBP 2012

SBP 2012

Racing bike B

Type of brake : without ABS

Mass : 220.0 kg

Racing bike C

Type of brake : ABS

(Antilock Brake System)

Mass : 208.0 kg

Racing bike D

Type of brake : ABS

(Antilock Brake System)

Mass : 242.0 kg

Diagram 3

[10 marks]

Question 4 [Force and Pressure]

Diagram 4 shows the parts of brake systems car.

Diagram 4

Table 4 shows the specifications of components that can be used in brake systems , P,Q,R, S and T.

Based on Table 4;You are required to determine the most suitable brake system and explain the

suitability of the aspects in Table 4

Brake fluid

Brake pedal

Brake pads

Brake disc

Page 29: Modul Perfect Score SBP Fizik SPM 2012

29

Physics Perfect Score SBP 2012

SBP 2012

Brake

system

Specifications of components in a car brake system

Specific heat capacity

of brake disc

J kg-10 C-1

Melting point

of brake disc 0 C

Compression of

brake fluid

The material

use of brake

pads

P 360 930 Difficult ceramics

Q 2400 1220 Difficult steel

R 890 580 Easy ceramics

S 2210 1940 Difficult ceramics

T 1460 2070 Easy steel

Table 4

[10 marks]

Question 5 [Force and Pressure]

You are asked to investigate the characteristics of each backhoes in table 11 and choose a backhoe

that can do heavy works, an example of a backhoe is shown in diagram 11.2. Explain the suitability of

the characteristics each backhoes. Determine the most suitable backhoe. Give reason for your choice

Type of

Backhoe

Characteristics of Backhoe

Size of tyre Fluids used in

hydraulic system Mass Base area

Centre of

gravity

M Large Liquid Large Large Low

N Large Liquid Small Large Low

P Large Gas Large Small High

Q Medium Liquid Large Medium Low

R Large Liquid Large Medium High

Table 11

Page 30: Modul Perfect Score SBP Fizik SPM 2012

30

Physics Perfect Score SBP 2012

SBP 2012

[10 marks]

Question 6 [Force and Pressure]

You are requested to choose a suitable wing to be installed with the body of the aircraft. By referring to

the information given in Table 11.1, explain the suitability of each characteristic and suggest the most

suitable wing to be installed with the body of the aircraft.

Design

Shape of cross section of wing

Area of

wing/m2

Density of

wing material

/ kg m-3

Difference in

speed of air

above and

below the wing

/ m s-1

P

40.0

2100

10.0

Q

41.5

2300

0.0

R

42.5

2000

0.0

S

38.2

2050

8.0

Table 11.1 shows the characteristic of four designs of the aircraft wings.

[10 marks]

Page 31: Modul Perfect Score SBP Fizik SPM 2012

31

Physics Perfect Score SBP 2012

SBP 2012

Question 7 [Force and Pressure]

Diagram 11.5 shows a hot air balloon.

Diagram 11.5

Table 11.1 shows four hot air balloon with different specifications.

Hot air balloon

Volume of the

balloon

(envelope)

Material used for

the balloon

Material used for

the basket

Temperature of air

inside the balloon

J 560 m3 Nylon Aluminium 500C

K 2800 m3 Nylon Rattan

990C

L 4 m3 Cotton Aluminium 500 C

M 25 m3 Cotton Rattan

1200 C

Table 11.1

You are required to determine the most suitable hot air balloon which can travel at higher

altitude. Explain the suitability of each of the characteristic of the balloon. Choose the most

suitable balloon and justify your choice.

[10 marks]

Question 8 [Force and Pressure]

As a researcher you are assigned to investigate the characteristics of four types of liquid that are

suitable to be used as a coolant for a car engine.

Table 5 shows the characteristics of the liquids.

Table 5

character

istics

Liquid

Boiling point

/ oC

Viscosity Specific heat

Capacity / J

kg-1 C-1 .

Ability to react

with metals

J 121 High 5500 High

K 128 Low 4750 Low

L 210 High 1195 Low

M 101 Low 3588 medium

Balloon

Basket

Page 32: Modul Perfect Score SBP Fizik SPM 2012

32

Physics Perfect Score SBP 2012

SBP 2012

(i) Explain the suitability of the characteristics of the liquid to be used as a coolant for the car engine.

(ii) Determine the most suitable liquid to be used and give a reason for your choice.

[10 marks]

Question 9 [Light]

Diagram 6 shows an astronomical telescope consist of objective lens and eye piece. An astronomical

telescope is used to view very large objects like moon.

Diagram 6

Table 7 shows the characteristics of four different simple astronomical telescopes.

Telescope Type of Objective

lens

focal length of

objective of, fo

/cm

The distance

between two

lenses / D

Diameter of the

objective lens /cm

S Convex 40 D <fo+fe 5.0

T Concave 10 D >fo+fe 5.0

U Convex 10 D <fo+fe 2.5

V Concave 40 D >fo+fe 2.5

Table 6

Explain the suitability of each characteristicof the telescope and determine the most suitable telescope

to be used to observe very far object. Give reason for your choice.

[10 marks]

Page 33: Modul Perfect Score SBP Fizik SPM 2012

33

Physics Perfect Score SBP 2012

SBP 2012

Question 10 [Electricity]]

Table 12.1 shows four heating elements F, G, H and J with different specifications. Three identical eating

panels are needed to be fixed on three sides of an electric dryer.

Heating

element

Diameter

of wire

Type of heating panel

Arrangement

of heating

panels

Melting

point

F Thick

Straight wire

Parallel circuit

Low

G Thin

Coil wire

Parallel circuit

High

H Thin

Straight wire

Series circuit

High

J Thick

coil wire

Parallel circuit

High

Table 12.1

You are required to determine the most suitable heating element that can produce highest

amount of heat faster.

Study the specifications of all the four heating elements based on the following aspects:

(i) Diameter of the wire.

(ii) Type of heating panel

(iii) Arrangement of three heating panels.

(iv) Melting point of the wire.

Explain the suitability of each aspects and then determine the most suitable heating

element.

Give a reason of your choice.

[10 marks]

Question 11 [Electromagnetism]

Question [Electromagnet]

Diagram 12.2 shows four types of moving coil ammeter, R, S, T and U to measure small direct current.

You are required to determine the most suitable moving coil ammeter to measure the small direct

current effectively.

Page 34: Modul Perfect Score SBP Fizik SPM 2012

34

Physics Perfect Score SBP 2012

SBP 2012

Moving coil

ammeter R

Moving coil

ammeter S

Page 35: Modul Perfect Score SBP Fizik SPM 2012

35

Physics Perfect Score SBP 2012

SBP 2012

Moving coil

ammeter T

Moving coil

ammeter U

Diagram 12.2

You are required to determine the most suitable moving coil ammeter to measure small direct

current effectively.

Study the specification of all the four moving coil ammeters based on the following aspects:

(i). The shape of the permanent magnet and core [2 marks]

(ii). The material of the core [2 marks]

(iii) The stiffness of the hair spring [ 2 marks]

(iv) The type of scale of the ammeter [2 marks]

Page 36: Modul Perfect Score SBP Fizik SPM 2012

36

Physics Perfect Score SBP 2012

SBP 2012

Explain the suitability of each aspect and then determine the most suitable moving coil

ammeter. Give a reason for your choice.

[2 marks]

Question 12 [Electromagnetism]

The transmission of electricity over the National Grid Network uses high voltage cables. You are assigned

to study the characteristics of cables which could be used as transmission cable. Table 7 shows the

characteristics of four transmission cables.

Cable

Resistivity /Ωm-1

Density / kg m-3

Rate of

oxidation

Rate of thermal expansion

P 3.0 x l0-7 5 x l05 Low High

Q 1.8 x l0-8 2 x l03 Low Low

R 7.5 x l0-7 8 x l02 High Medium

S 7.0 x l0-8 4 x l03 Medium High

Based on the table 7;

(i) Explain the suitability of the characteristics of the cables to be used as transmission cable.

(ii) Determine the most suitable transmission cable to be used and give reasons for your choice.

[10 marks]

Table 7

Page 37: Modul Perfect Score SBP Fizik SPM 2012

37

Physics Perfect Score SBP 2012

SBP 2012

Question 13 [Electronic/electromagnetism]

You are asked to investigate the design and the characteristics of four alternating current generators

shown in Table 8. Explain the suitability of each characteristic of the alternating current generators and

determine the alternating current generator which can supply a large direct current to an electrical

component X shown in Diagram 8.

Diagram 8

Generator

Density of

the coil / kg

m–3

Frequency of

rotation

Rectification circuit

G 9200 High

H 11600

Medium

I 8960 High

J 10500 Medium

[10 marks]

x

Page 38: Modul Perfect Score SBP Fizik SPM 2012

38

Physics Perfect Score SBP 2012

SBP 2012

Question 14 [Electronic]

As a research engineer in a factory, you are asked to investigate the characteristics of several

substances in order to produce p-type or n-type to produce semiconductor diode.

Table 9 shows the characteristics of five semiconductors P, Q, R, S and T

Semiconductor

Electron Valens of

intrinsic

semiconductor

Electron Valens of

doping substance

Size of the doping atom compared

with the size of the atom relative to

intrinsic semiconductor atom

P

5

2

Big

Q

4 5

Small

R 3 4 Small

S 5 2 Almost the same

T 4 3

Almost the same

Table 9

Explain the suitability of the characteristics of the semiconductor P, Q, R, S and T to be used in the

production of a semiconductor diode. Give reasons for your choice

Which type of intrinsic semiconductor below is the most suitable to be used. Give your reason for your

answer.

Type of intrinsic

semiconductor

Silicon

Germanium

[ 10 marks]

Page 39: Modul Perfect Score SBP Fizik SPM 2012

39 X A-Plus Physics Module 2012

Question 15 [Radioactivity]

As a researcher, you are assigned to investigate the characteristics of radioactive substances with to

be used for the treatment of cancer.

Table 10 shows radioactive rays directed towards the cancer cells in a patient’s brain.

Radioactive Type of radiation Half-life State of matter Ionizing power

J Beta 6 hours Liquid High

K Gamma 1620 years Solid Low

L Gamma 5 years Solid Low

M Beta 15 days Liquid High

Table 10

(i) Based on Table 10, explain the suitable properties of the radioactive substances for use to kill

cancer cells in patients brains.

(ii) Determine which radioactive substance is the most suitable for the treatment of cancer cells in a

patient and give your reasons.

[10 marks]

Page 40: Modul Perfect Score SBP Fizik SPM 2012

40

X A-Plus Physics Module 2012

X A-PLUS 2012

SECTION V– CONCEPTUALIZATION (Paper 2 Section A – Question 5/6; Section B )

Question 1 [Force and Pressure]

Diagram 1(a) and Diagram 1(b) show two solid spheres A and B with different density placed in the water.

Diagram 1(a) Diagram 1 (b)

Based on Diagram 1(a) and Diagram 1(b),

(i) compare the density of sphere A and sphere B. [ 1 mark ]

(ii) compare the weight of sphere A and sphere B [ 1 mark ]

(iii) compare the weight of water displaced by sphere A and sphere B [ 1 mark ]

(iv) relate the weight of sphere and the weight of water displaced [ 1 mark ]

(v) relate the weight of water displaced and upthrust [ 1 mark ]

Question 2 [Force and Pressure]

A fisherman finds that his boat is at different levels in the sea and in the river, although the boat carries the

same load. The density of sea water and river water is 1025 kg m-3 and 1000 kg m-3 respectively.

In the sea In the river

Diagram 2(a) and Diagram 2(b) illustrate the situation of the boat in the sea and in the river.

(a) What is meant by density? [1 mark]

(b) Based on Diagram 2(a) and Diagram 2(b)

(i) Compare the level of the boat in the sea water and in the river water. [1 mark]

(ii) Compare the volume of water displaced by the boat in the sea and in the river. [1 mark]

(iii) Compare the density of sea water and river w [1 mark]

(c) (i) Relate the volume of water displaced to the density of water. [1 mark]

(ii) Deduce relationship between weight of the boat and the weight of the water

displaced. [1 mark]

(d) Name the physics principle that explains the situation above. [1 mark]

DIAGRAM 2(a) DIAGRAM 2(b)

Page 41: Modul Perfect Score SBP Fizik SPM 2012

41

X A-Plus Physics Module 2012

X A-PLUS 2012

Question 3 [Heat]

Diagram 3(a) shows a balloon filled with air attached to a test tube before and after the test tube is

heated.

Diagram 3(b) shows a pingpong ball before and after it is poured with boiled water.

(i) (ii)

(a) (i) Observe Diagram 3(a) and Diagram 3(b).State two similarities about the air inside the balloon and

ping pong ball. [2 marks]

(ii) Compare the mass of air in Diagram 3(a)(i) with Diagram 3(a)(ii); and Diagram 3(b)(i) with Diagram

3(b)(ii). [1 mark]

(b) (i) Based on your observation in Diagram 3(a) and Diagram 3(b), state the relationship between

the physical quantities in (a) (i). [1 mark]

(ii) Name physics law involved in (b)(i). [1 mark]

(iii) Using observation in Diagram 3(a) and Diagram 3(b), explain the physics law stated in b(ii)

using kinetic theory of matter. [3 marks]

Diagram 3(b)

Diagram 3(a)

(i) (ii)

Page 42: Modul Perfect Score SBP Fizik SPM 2012

42

X A-Plus Physics Module 2012

X A-PLUS 2012

Question 4 [Wave]

Diagram 4.1 shows the pattern of the water wave after passing through a gap.

The experiment was repeated with different wavelength of waterpassing through the same gap. The wave

pattern is as shown in Diagram 4.2.

Diagram 4.1 Diagram 4.2

(a) What is wavelength? [1 mark ]

(b) Based on Diagram 4.1 and Diagram 4.2, compare

(i) the wavelength before passing through the gap

(ii) the wavelength before and after passing through the gap

[2 marks]

(c) Compare the wave pattern in Diagram 4.1 and Diagram 4.2 after the wave passed through the

gap. [1 mark]

(d) Based on your answers in ( b) and (c), state the relationship between the wavelength and the

wave pattern after passing through the gap. [1 mark] [

(e) Name the wave phenomenon which occurs in Diagrams 4.1 and 4.2. [1 mark]

Question 5 [Electromagnetism]

Diagram 5.1 shows a bar magnet with northpole at point P and Diagram 5.2 shows a bar magnet with

south pole at point Q which are moved towards the solenoid to produce current.

DIAGRAM 5.1 DIAGRAM 5.2

Page 43: Modul Perfect Score SBP Fizik SPM 2012

43

X A-Plus Physics Module 2012

X A-PLUS 2012

a) Observe the diagrams and state two differences between them. [2 marks]

b) What is the polarity of the solenoid at point P and Q when the magnet is moved towards the

solenoid?

P : …………………………… Q : ………………………… [2 marks]

c) What is the relationship between the number of turns and the magnitude of induced current?

[1mark]

d) Name the law involved in (c). [1mark]

e) Suggest another method to increase the deflection of the pointer. [1mark]

f) State an instrument that uses the application of induced current. [1mark]

Question 6 [Force and Motion]

Diagrams 6.1 and 6.2 show a load is being lift up.

(a) What is gravitational potential energy? [1mark]

(b) Based on Diagrams 6.1 and 6.2 , compare the position of the loadafter being lifted up, the

gravitational potential energy and the work done.

State the relationship between

- the position of the load and the work done in lifting the load.

- The gravitational potential energy and the work done

[5marks]

Diagram 6.1 Diagram 6.2

Ground Ground

Page 44: Modul Perfect Score SBP Fizik SPM 2012

44

X A-Plus Physics Module 2012

X A-PLUS 2012

Question 7 [Force and Motion]

Diagram 7shows a 50 sen coin and a leaf falling in a vacuum container. The coin is heavier than the leaf.

Diagram 7

Using the diagram shown and the information given about the weight of the two objects, compare the

mass of the coin and the leaf, the time taken to fall, the falling position of the coin and the leaf,the

gravitational acceleration of the coins and the leaf. Deduce the relationship between the mass and the

gravitational acceleration of falling object.

[5 marks]

Question 8 [Force and Pressure]

Diagram 8(a), Diagram 8(b) and Diagram 8(c) show a rock being hung on a spring balance in the air,

immersed in water and cooking oil respectively. The reading of the spring balance for each situation is as

shown in Diagram 8.

Diagram 8

Using Diagram 8(a), Diagram 8(b) and Diagram 8(c), compare the spring balance reading, the weight lost

of the rock and the density of the water and the cooking oil.

Relate the weight lost and the density to deduce a relevant physics concept.

[5 marks]

Page 45: Modul Perfect Score SBP Fizik SPM 2012

45

X A-Plus Physics Module 2012

X A-PLUS 2012

Question 9 [Force and Pressure]

Diagram 9(a) shows a hot air balloon carry up the loads at a certain height in the morning and Diagram

9(b) shows the same hot air balloon carry up the loads at a certain height in the afternoon. The hot air

balloon used helium gas at the same temperature in both situations.

Diagram 9

Using Diagrams 9(a) and 9(b), compare the density of the air, the load that can be carried up by the hot

air balloon and the height of the hot air balloon from the ground.

Relate the buoyant force with the density of the air to make a deduction regarding the relationship

between the density of the air and the weight of the load carried by the hot air balloon.

[5 marks]

Question 10 [Force and Pressure]

Diagram10.1, Diagram10.2and Diagram10.3 show a fisherman pulling the fishing net out of the river. In

Diagram10.1, the fisherman finds it easy to pull up the fishing net while most of the fish is in the water.

However as more and more of the net is out of the water it gets harder to pull up the net as shown in

Diagrams10.2 and 10.3.

Diagram 10.1 Diagram 10.2 Diagram 10.3

Page 46: Modul Perfect Score SBP Fizik SPM 2012

46

X A-Plus Physics Module 2012

X A-PLUS 2012

Using Diagrams10.1, 10.2 and 10.3, compare the mass of the fishand the volume of the fishing net

immersed in the water.

Relate the weight of water displaced with the amount of force required to lift the net and the buoyant

force, and deduce a relevant physics concept.

[5 marks]

Question 11 [Light]

Diagram 11(a) and Diagram 11(b) show two rectangular glass blocks with different optical density and

refractive index. Ray of light is directed toward the glass blocks with the same angle of incidence 30°.

Density = 2600 kgm-3 Density = 2670 kgm-3

Diagram 11(a) Diagram 11(b)

Based on Diagram 11(a) and Diagram 11(b), compare the density, the refractive index and the angle of

refraction of the glass blocks. Relate

- the angle of refraction, r and the density of the glass blocks.

- relate the angle of refraction, r and the refractive index of the glass blocks

[5 marks]

Question 12 [Light]

Diagram 12.1 and Diagram 12.2 show the parallel rays of light directed towards the convex lenses J and K.

Both the lenses produce real images. F is the focal point for each lens.

DIAGRAM 12.1 DIAGRAM 12.2

Page 47: Modul Perfect Score SBP Fizik SPM 2012

47

X A-Plus Physics Module 2012

X A-PLUS 2012

With reference to Diagram 12.1 and Diagram 12.2, compare the thickness of the lenses, the effects it has

on the refracted rays, and the focal length of the lens.Relate the thickness of the lens with the effect on the

refracted ray, to deduce a relationship between the thickness of the lens and the focal length.

[5 marks]

Question 13 [Wave]

Diagram 13.1 (a) and Diagram 13.2(a) show the apparatus set-up for a Young’s double-slit experiment, to

determine the wavelength of a monochromatic light. Diagram 13.1(b) and Diagram 13.2(b) show the

fringes formed on the screen for each situation.

Using the diagrams given, compare the distance between the double-slit and the screen, the distance

between two successive bright fringes, the number of fringes and the width of fringes.

Deduce the relationship between the distance between the double-slit and the screen, and the distance

between two successive bright fringes.

[5 marks]

Question 14 [Waves]

Diagram 14(a) and 14(b) show vibration of different thickness of guitar string.

Diagram 14(a)

Page 48: Modul Perfect Score SBP Fizik SPM 2012

48

X A-Plus Physics Module 2012

X A-PLUS 2012

Diagram 14(b)

When microphone is used to detect the sound waves of each guitar string, the traces displayed on the

oscilloscopes as shown in the diagrams.

(i) Using Diagram 14(a) and 14(b), compare the number of oscillations, amplitude of wave and

diameter of Guitar string.

(ii) State the relationship between the frequency of sound wave and

-diameter of the string

-pitch of the sound

[5 marks]

Question 15 [Electricity]

Diagram 15.1 and 15.2 show two identical resistors with resistance R connected to the ammeter, voltmeter,

switch and batteries in different ways.

When the switch is on, the ammeter and the voltmeter show a reading. Based on Diagram 15.1 and

Diagram 15.2, compare the type of circuit connection, the reading of ammeter, the reading of voltmeter

and the effective resistance of the circuit.

Relate the current flows in a circuit with the effective resistance to make a deduction regarding the

relationship between type of a circuit connection and the effective resistance.

[6 marks]

DIAGRAM 15.1 DIAGRAM 15.2

DIAGRAM 11.2

Page 49: Modul Perfect Score SBP Fizik SPM 2012

49

X A-Plus Physics Module 2012

X A-PLUS 2012

Question 16 [Electromagnetism]

Diagram 16(a) and Diagram 16(b) show the relative motion between the magnet and solenoid. The ends

of the coils are connected to a zero centre galvanometer.

Diagram 16(a) Diagram 16(b)

Using Diagram 16(a) and Diagram 16(b),

(i) compare the direction of the movement of the magnet

(ii) compare the deflection of the galvanometer pointer

(iii) Relate the movement of the magnet, the polarity at the top of the coil and the force acting on

the magnet to explain a relevant physics law.

[5 marks]

Question 17 [Electronics]

Diagram 17.1 and Diagram 17.2 show a bulb is connected to a diode and a dry cell.

Diagram 17.1 Diagram 17.2

Observe Diagram 17.1 and Diagram 17.2. Compare the condition of the two bulbs, the connection of the

diode. Relate the diode connection with

- the condition of the bulbs, and

- the current flow through the diode

Deduce a relevant physics concept.

[ 4 marks]

Page 50: Modul Perfect Score SBP Fizik SPM 2012

50

X A-Plus Physics Module 2012

X A-PLUS 2012

Question 18 [Radioactivity]

Table 18.1 shows a reaction equation and the total mass of atom before and after nuclear fission.

Nuclear Fission

Before Reaction After Reaction

Chemical Equation

Total mass of atom 240.06082 a.m.u 239.85830 a.m.u

TABLE 18.1

Table 18.2 shows reaction equation and the total mass of atom before and after nuclear fusion.

Nuclear Fusion

Before reaction After reaction

Chemical Equation

Total mass of atom 5.03013 a.m.u 5.01043 a.m.u

TABLE 18.2

Using the information in Table 18.1 and 18.2 only, compare the process of nuclear fission and nuclear

fusion,total mass of atombefore and after the reaction, and then relate the relationship between mass

and energy released.

[ 5 marks ]

Question 19 [Radioactivity]

Diagram 19(a) and Diagram 19(b) show the activities of two radioactive sources P and Q.

DIAGRAM 19(a) DIAGRAM 19(b)

Page 51: Modul Perfect Score SBP Fizik SPM 2012

51

X A-Plus Physics Module 2012

X A-PLUS 2012

Based on Diagram 19(a) and Diagram 19(b),

(i) State common characteristic of

- the shape of the graph

- the time taken for the activities of radioactive sources P and Q to become half of its initial value.

[2 marks]

(ii) determine the time taken for the activity of radioactive sources P and Q to become half of its

initial value.

[2 marks]

(iii) Name the physical quantity for the activity of a radioactive source tobecome half of its initial

value.

[1 mark]

SECTION VI – PROBLEM SOLVING [QUALITATIVE] (Paper 2 Section A: Question 7; Section B

Question 9/10 )

Question 1 [ Introduction In Physics]

You are required to give some suggestions to design an efficient alcohol thermometer to be used in physics

research expedition at North Pole.

Using your knowledge about heat and properties of materials, explain how to build a thermometer which

can function effectively based on the following aspects:

(i) Strength of thermometer

(ii) Sensitivity of thermometer

(iii) Design of the thermometer so that the scale can easily be read

(iv) Freezing point of the liquid

(v) Thickness of the glass bulb’s wall

[10 marks]

Question 2 [ Forces and Motion]

Diagram below shows a rocket.

Page 52: Modul Perfect Score SBP Fizik SPM 2012

52

X A-Plus Physics Module 2012

X A-PLUS 2012

You are required to give some suggestions to design a rocket which can travel in the outer space with

higher acceleration.

Using the knowledge on forces and motion and the properties of materials, explain the suggestions based

on the following aspects:

(i) the shape of the rocket

(ii) the material used to build the rocket

(iii) additional supply needed that enable the rocket to move in outer space

(iv) the structure of the rocket to accelerate.

(v) size of the combustion chamber

[10 marks]

Question 3 [ Forces and Motion]

Diagram below shows an athlete throwing a javelin

Using appropriate physics concepts, explain the use of suitable equipment and techniques to improve his

performance.

Your answer should include following aspects:

(i) Characteristics of material used for javelin

(ii) Shape of javelin

(iii) Motion of the athlete

(iv) How the javelin should be thrown

[10 marks]

Question 4 [ Forces and Motion]

Diagram 9.3 shows a badminton player in a competition.

.

You are required to give some suggestions to design the shuttle and racquet used in the competition. Using

your knowledge of motion, forces and properties of material, state and explain the suggestions based on

the following aspects:

(i) Shape of the shuttle.

(ii) Characteristic of the material used for shuttle.

Shuttle/ Bulutangkis

Racquet / Raket

Diagram 9.3 / Rajah 9.3

Page 53: Modul Perfect Score SBP Fizik SPM 2012

53

X A-Plus Physics Module 2012

X A-PLUS 2012

(iii) Material used for the base of the shuttle.

(iv) Material used for the string of the racquet.

(v) Tension of the string of the racquet.

[10 marks]

Question 5 [ Forces and Pressure]

The manager of a carnival near your home seeks your advice on handling a hot air balloon. The balloon

should be able to rise to about the height of a five-storey building, carry up to three people and can be

brought down to the same spot after a certain time.

Explain your suggestion taking into account:

(i) Size of the envelope

(ii) Characteristic of the materials used for the envelope

(iii) Equipment required to rise up the balloon.

(iv) Characteristics of the material used for the basket,

(v) the best times in a day to launch the balloon

[10 marks]

Question 6 [ Heat]

Diagram below shows food being fried in a wok of cooking oil

Suggest and explain how the food to be fried can be cooked in a short time based on the following

aspects of material of the wok and the cooking oil.

a. Material of the wok

Page 54: Modul Perfect Score SBP Fizik SPM 2012

54

X A-Plus Physics Module 2012

X A-PLUS 2012

(i) Specific heat capacity

(ii) Thermal conductivity

(iii) Melting point

b. Cooking oil

(i) Specific heat capacity

(ii) Boiling point

[10 marks]

Question 7 [ Heat]

A family is having a picnic at Port Dickson beach. A container is used to stor the packet drinks as shown in

diagram below.

Use appropriate concepts in physics, explain the modifications required to the above container so as to

effectively cool packet drinks in a shorter time and keep the packet drinks remain cold for a longer period.

State and explain the suggestion based on the following aspects:

(i) Materials added in the container

(ii) Specific heat capacity of the container

(iii) Colour of the container

(iv) Characteristics of the material used for the container.

[10 marks]

Question 8 [ Heat/Light]

Diagram below shows a simple solar tank as a water heater

Using appropriate physics concept, explain the modifications that can be used to make a solar more

efficient.

Your answer should include the following aspects:

(i) Type of mirror

Page 55: Modul Perfect Score SBP Fizik SPM 2012

55

X A-Plus Physics Module 2012

X A-PLUS 2012

(ii) Radius of curvature

(iii) Color of the tank wall

(iv) Specific heat capacity and other suitable aspect

(v) Size of the mirror

[10 marks]

Question 9 [ Light ]

Diagram 9.3 shows two cars, R and S , travelling in the opposite directions, passing through a sharp band. A

mirror is placed at X .

Diagram 9.3

Using the knowledge on reflection of light, explain your choice of mirror to help the driver to see an

approaching car based on the following aspect:

(i) the type of mirror

(ii) the diameter of the mirror

(iii) the characteristics of material used for the mirror

(iv) the thickness of the mirror

(v) The position of the mirror

[10 marks]

Question 10 [ Waves]

Diagram 10.3, shows the location of housing area. The residents of housing area at P receive clearer

television signal compare to the residents of housing area at Q where it is located behind the hill.

Hill Housing area Q

Broadcasting station

Diagram 10.3

Transmitter

Housing area P

Page 56: Modul Perfect Score SBP Fizik SPM 2012

56

X A-Plus Physics Module 2012

X A-PLUS 2012

As a researcher, you are required to give suggestions about the modifications of transmission television

signal from broadcasting station so that the residents of housing area at Q are enable to receive better

signal.

State and explain the modification based on the following aspects:

(i) the frequency of the signals

(ii) the location of the transmitter

(iii) the number of the transmitter

(iv) the strength of the signals

(v) the distance between two transmitters

[10 marks]

Question 11 [ Electricity]

Diagram 4 shows the lamps in a domestic lightning circuit are connected in parallel.

Diagram4

The circuit is not complete and not efficient for electrical energy consuming and less safety.

Suggest modifications that need to be done to the circuit to improve safety, produce the lamps lights up

with normal brightness and to increases the efficiency of electrical energy consuming.

State and explain the modification based on the following aspects:

(i) switch

(ii) connection between bulb C and D

(iii) suitable voltage for the bulb

(iv) safety aspect

(v) suitable device to be connected to bulb B.

[10 marks]

Question 12 [ Electromagnets]

Diagram below shows a cross section of a simple seismometer which is used to detect the earth motion

and then convert it into the electrical signals.

Diagram 6

Page 57: Modul Perfect Score SBP Fizik SPM 2012

57

X A-Plus Physics Module 2012

X A-PLUS 2012

You are required to give suggestions to design the seismometer which can work efficiently. Using your

knowledge, explain the suggestion based on the following aspects;

(i) the stiffness of the spring

(ii) density of the load

(iii) the shape of the magnet

(iv) the type of the electrical coil

(v) how it is used to detect small motion

[10 marks]

Question 13 [ Electronics]

Diagram 8 shows a control circuit for a simple fire alarm system.

Diagram 8

You are required to give suggestions to design the circuit so that it can switch on the transistor and sound

an alarm when either one of the sensors gets hot. State and explain the suggestions based on the following

aspects:

(i) The type of gate X

(ii) Component used to detect heat and it position

(iii) The position of the alarm.

(iv) The use of extra components in the circuit and its positions to switch on the 240 V, 12 W alarm.

[10 marks]

Question 14 [ Electronics]

Diagram below shows a shadow is formed on fluorescent screen of the Maltase cross tube.

Page 58: Modul Perfect Score SBP Fizik SPM 2012

58

X A-Plus Physics Module 2012

X A-PLUS 2012

Maltase cross tube in Diagram 10.3 is not suitable for measuring the frequency of the sound waves.

Suggest modifications that can be made to the Maltase cross tube in Diagram 10.3 to transform it into

Cathode Ray Oscilloscope that can measure the frequency of the sound waves.

In your suggestions, state the components that are used and their functions based on the following aspects:

(i) the electron gun

(ii) the deflection system

[10 marks]

Question 15 [ Radioactive]

Diagram 10.3 shows a radioactive source is handled by a scientist.

The method shown is not safe.

Suggest and explain;

(i) The equipment to be used in handling a radioactive source.

(ii) Modifications to the storing method to ensure safe keeping of the radioactive source.

(iii) Other precautions that need to be taken when handling a radioactive source.

[ 10 marks ]

SECTION VII– PROBLEM SOLVING [QUANTITATIVE] (Paper 2 Section C Question 11/12 )

1. (i) A toy car of mass 1.5 kg is moving at a constant velocity of 40 ms-1 collides with a wall and bounce

back at a velocity of 35 ms-1. What is the impulse applied on the car?

(ii) If the time of collision between the toy car and the wall takes 0.8 s, what is the impulsive force

applied on the toy car?

2. Diagram shows a car is moving with a constant velocity when the engine provides a thrust of 900 N.

The car is then accelerates at 2 m s-2. The total mass of the car is 1 000 kg.

900 N

Page 59: Modul Perfect Score SBP Fizik SPM 2012

59

X A-Plus Physics Module 2012

X A-PLUS 2012

(i) What is the frictional force between the tyre& the road?

(ii) What is the force exerted by the engine when the car accelerates at 2 m s-2 ?

3. A racing bike of mass 202 kg accelerates from rest to its velocity of18 kmh-1 in 10 s.

(i) Calculate the acceleration of the racing bike.

(ii) Calculate the force acting on the racing bike.

4. Justin conducted an experiment to prove Hooke’s Law. The observation is plotted as the graph shown

below.

(i) Calculate the spring constant of spring P and spring Q.

(ii) Calculate the work done by spring P to extend the spring to 10 cm.

5. Diagram shows a boat which has a safety limit line, L. The volume of the boat under the line L is 4 m3.

The mass of the boat is 250 kg. (Density of water = 1 000kgm-3 )

(i) Calculate the volume of water displaced by the boat.

(ii) What is the mass of the maximum load that can be carried safely by the boat?

6. An aircraft has a mass of 800 kg and the surface area of its wing is 40 m2.

(i) If the air pressure below the wing is greater than the air pressure above the wing by 500 Nm-2 ,

calculate the force exerted on the wing.

(ii) Determine the resultant force exerted on the wing of the aircraft. State the direction of the

resultant force.

(iii) Calculate the vertical acceleration of the aircraft.

L

Page 60: Modul Perfect Score SBP Fizik SPM 2012

60

X A-Plus Physics Module 2012

X A-PLUS 2012

7. Diagram shows a hydraulic jack with a cross sectional area of the smaller piston is 0.2 m2 and the larger

piston is 1.2 m2.

(i) If a force of 6N is exerted on the smaller piston, what is the output force acted on the larger

piston?

(ii) If the smaller piston moves downward by 1.2 cm, what is the distance moved by the larger piston?

8. The weight of the boat is 15 000 N. The maximum volume of water that can be displaced by the boat is

2.0 m3.

(i) Calculate the buoyant force exerted on the boat.

[Density of the sea water is 1020 kgm-3]

(ii) A heavy box is put on the boat. Calculate the maximum weight of the box so that the

boat will not sink.

9. 0.004 m3 of cooking oil was heated by using electric deep fryer of power rating 240V , 2500W. The

temperature of the oil rises from 30°C to 160 °C. Assuming all the electrical energy was used to

increase the temperature of oil only and no heat loss to the surrounding.

Calculate:

(i) mass of the cooking oil

. (ii) the time taken to heat the cooking oil.

[Specific heat capacity of oil is 2000J kg–1 °C–1. Density of oil is 800 kg m-3]

10. An object is placed at a distance of 20 cm from a concave lens of focal length 15 cm.

(i) Calculate the image distance

(ii) Calculate the magnification of the image

(iii) State the characteristics of the image formed.

11. A student is using a magnifying glass with focal length of 5 cm to observe a small ant at a distance

of 2 cm.

(i) Calculate the image distance.

(ii) Determine the linear magnification of the image of the ant.

Page 61: Modul Perfect Score SBP Fizik SPM 2012

61

X A-Plus Physics Module 2012

X A-PLUS 2012

12. Diagram shows three light rays from a point O travelling in a glass block towards points X, Y and Z.

The refractive index of the glass block is 1.5.

Calculate the angle

(i) ϴ

(ii)

(iii) β

13. A wooden bar P vibrates on a water surface of a ripple tank at a frequency of 5 Hz.

The water wave produced is shown in the diagram below.

(i) The distance between three consecutive crests is 8.0 cm.

What is the wavelength, λ, of the water wave?

(ii) What is the frequency of the water wave?

(iii) Calculate the speed of the water wave in the ripple tank.

30oα 50o

Y X Z

β

O

Page 62: Modul Perfect Score SBP Fizik SPM 2012

62

X A-Plus Physics Module 2012

X A-PLUS 2012

14. Diagram shows a U-shaped soft iron core is wound with insulated copper wire PQ and RS. An a.c.

supply of 240 V is connected at the ends of PQ and a bulb of 12V, 60W is connected at the ends of RS.

(i) If the bulb lights up with normal brightness, determine the ratio of the number of turns in the coil

PQ to the number of turns in the coil RS.

(ii) Calculate the output current.

(iii) If the efficiency of the transformer is 80%, calculate the current in the primary coil.

15. A potential difference of 3 kV is applied across the cathode and anode of an electron gun.

Calculate the maximum velocity of the electron produced.

Given the charge of an electron, e = 1.6 x 10-19 C, mass of an electron, m = 9.0 x 10-31 kg.

16. A cup of milk is contaminated with iodine-131. The half-life of iodine-131 is 8 days.

(i) Iodine-131 is no longer a threat once its activity decay to one-eighth of its original activity. After

how many days will the milk be safe to drink?

(ii) The initial mass of a sample of iodine-131 is 20 mg. How much of iodine-131 will remain after 32

days?

Page 63: Modul Perfect Score SBP Fizik SPM 2012

63

X A-Plus Physics Module 2012

X A-PLUS 2012

SECTION VIII A – Paper 3 Section A

1 A student carries out an experiment to study the relationship between the angle of incidence, i, and

the angle of refraction, r, when a light ray passes from air to a semicircular glass block. The apparatus

set-up for this experiment is shown in Diagram 1.1.

Diagram 1.1

The ray box is adjusted so that a ray of light enters the semicircular glass block at an angle of

incidence, i = 15o.The angle of refraction, r, is measured with a protractor.The experiment is repeated

with angles of incidence, i = 30o, 45o, 60o and 75o.

The corresponding measurements made by the protractor are shown in Diagrams 1.2, 1.3, 1.4, 1.5

and 1.6.

i

r

Ray box

Glass block

Incident ray

Refracted ray

Page 64: Modul Perfect Score SBP Fizik SPM 2012

64

X A-Plus Physics Module 2012

X A-PLUS 2012

i = 15o

sini = …………

r = ……….

sinr = …………

15o

i = 30o

sini = …………

r = ……….

sinr = …………

30o

Diagram 1.2

Diagram 1.3

Page 65: Modul Perfect Score SBP Fizik SPM 2012

65

X A-Plus Physics Module 2012

X A-PLUS 2012

Diagram 1.4

Diagram 1.5

i = 45o

sini = …………

r = ……….

sinr = …………

45o

60o

i = 60o

sini = …………

r = ……….

sinr = …………

Page 66: Modul Perfect Score SBP Fizik SPM 2012

66

X A-Plus Physics Module 2012

X A-PLUS 2012

Diagram 1.6

(a) For the experiment identify:

(i) The manipulated variable

[1 mark]

(ii) The responding variable

[1 mark]

(iii) The constant variable

[1 mark]

(b) For this part of the question, write your answers in the spaces provided in the corresponding

diagrams.

Based on Diagrams 1.2, 1.3, 1.4, 1.5 and 1.6:

(i) Record the readings, r, of the protractor.

[2 marks]

(ii) For each value of i, calculate and record the value of sin i.

[1 mark]

(iii) Calculate sin r for each value of r in 1(b)(i).

Record the value of sin r.

[2 marks]

i = 75o

sini = …………

r = ……….

sinr = …………

75o

Page 67: Modul Perfect Score SBP Fizik SPM 2012

67

X A-Plus Physics Module 2012

X A-PLUS 2012

(c) Tabulate your results for all values of i, sin i and sin r in the space below.

[2 marks]

(d) On the graph paper provided, plot a graph of sin i against sin r.

[5 marks]

(e) Based on your graph in 1(d), state the relationship between sin i and sin r.

[1 mark]

Page 68: Modul Perfect Score SBP Fizik SPM 2012

68

X A-Plus Physics Module 2012

X A-PLUS 2012

Graph of sin i against sin r

Page 69: Modul Perfect Score SBP Fizik SPM 2012

69

X A-Plus Physics Module 2012

X A-PLUS 2012

2 A student carries out an experiment to investigate the relationship between displacement, d and time,

t of an object. The result of the experiment is shown in the graph of d against t, as in Diagram 3.1.

(a) Based on the graph in Diagram 3.1,

(i) state the relationship between d and t

[1 mark ]

(ii) determine the value of d when t = 0.4 s. Show on the graph, how you determine the

value of d.

d =

[2 marks]

(b) The acceleration, a, of the object and time, t, are linked mathematically by the equation

a = 2 m

t

where m is the gradient of the graph.

(i) Calculate the gradient, m, when t = 0.5 s. Show on the graph how you determine m.

m =

[4 marks]

(ii) Calculate the value of a when the time t = 0.5 s.

a =

[2 marks]

The gradient of the graph, m, represents one physical quantity.

(i) Name the physical quantity that represents the value of m

[1 mark]

(ii) State how the physical quantity in (c) (i) varies with time.

[1 mark]

(d) State one precaution that should be taken to improve the results of this experiment.

[1 mark]

Page 70: Modul Perfect Score SBP Fizik SPM 2012

70

X A-Plus Physics Module 2012

X A-PLUS 2012

Page 71: Modul Perfect Score SBP Fizik SPM 2012

71

X A-Plus Physics Module 2012

X A-PLUS 2012

SECTION VIII B– EXPERIMENT (Paper 3 Section B)

Based on the diagrams in Questions 1- 15,

(a) makeone suitable inference .

(b) stateone appropriate hypothesis that could be investigated.

(c ) describe how you would design an experiment to test your hypothesis

In your explanation, state clearly the following :

(i) The aim of the experiment

(ii) The variables in the experiment

(iii) The list of apparatus and materials

(iv) The arrangement of the apparatus

(v) the procedures of the experiment, which includes the method of controlling the

manipulated variable and the method of measuring the responding variable

(vi) the way you would tabulate the data

(vii) the way you would analyse the data

No. Situation

Q1

Diagram 1(a) and Diagram 1(b) show a woman is taking a ride in two different cars.

In Diagram 1(a), when the car just departs, she experiences a pushing force, F from the seat and the

car moves from rest to 25 m s-1 in 10 s.

In Diagram 1(b), when she is riding a race car with more powerful engine, she experiences a greater

force and the car moves to a higher speed from rest in the same period.

Diagram 1(a) Diagram 1(b)

Page 72: Modul Perfect Score SBP Fizik SPM 2012

72

X A-Plus Physics Module 2012

X A-PLUS 2012

No. Situation

Q2

Diagram 2(a) and 2(b) show a car and a motorbike of different masses. It is observed that if the car

takes up same power to produce same force as the motorbike, the car has lower acceleration than

the motorbike.

Diagram 2(a) Diagram 2(b)

Q3

Diagram 3(a) shows the position of the driver when a moving car of 80 km h-1 stops suddenly.

Diagram 3(b) shows the position of the driver when a moving car of 120 km h-1 stops suddenly.

Diagram 3 (a) Diagram 3(b)

Page 73: Modul Perfect Score SBP Fizik SPM 2012

73

X A-Plus Physics Module 2012

X A-PLUS 2012

No. Situation

Q4

Diagrams 3.1 and Diagram 3.2 show a launching mechanism of a toy gun consist of a spring. It is

observed that when the spring is compressed and the gun fired vertically, the gun launch the

projectile from rest to a different maximum height.

Q5

Diagram 5 shows a lady and a man walking on a wooden floor. It is observed that the lady that

wearing high heel can damage a wooden floor badly but not a man (heavier) that wearing snickers.

Diagram 5

Page 74: Modul Perfect Score SBP Fizik SPM 2012

74

X A-Plus Physics Module 2012

X A-PLUS 2012

No. Situation

Q6

Diagram 6 (a) and 6(b) show a diver swimming in the sea water. The diver experiences more

discomfort to his body and ear in Diagram 6 (b)

Q7

Diagram 7(a) shows a device used to transmit thermal energy. The fins absorb energy from the sun

and the pipe transmits the energy along its length into 25 oC of cold water in a tank until it reaches

50oC. It is observed that the time taken, t to increase the temperature in Diagram 3.1 is more than that

in Diagram 3.2.

Diagram 7(a) Diagram 7(b)

t = 30 minutes t = 10 minutes

Energy from the

sun

1 m3 water tank

Energy from the

sun

1 m3 water tank

glass fin copper fin

Diagram 6(a) Diagram 6(b)

Page 75: Modul Perfect Score SBP Fizik SPM 2012

75

X A-Plus Physics Module 2012

X A-PLUS 2012

No. Situation

Q8

Diagram 8.1 and 8.2 show two pots of different size filled with boiling water. It is observed that the

temperature of the water in Diagram 4.1 drops at a faster rate than in Diagram 4.2.

Q9

Amira is out on a hot summer day and purchase a few balloons. When she gets home, she decides to

leave a couple outside in the hot air and bring the rest into her air-conditioned room. She notice that

the balloons inside and the balloons outside are slightly different shapes and sizes.

Diagram 8.1 Diagram 8.2

Page 76: Modul Perfect Score SBP Fizik SPM 2012

76

X A-Plus Physics Module 2012

X A-PLUS 2012

No. Situation

Q10

Diagram 10 (a) and 10 (b) show a pencil is placed in front of the lens. The image of the pencil is

formed when light moving through the convex lens

Q11

Diagram 11 (a) and11 (b)below show the fringes produced when red and blue monochromatic light

sourceswere used.

Diagram10(a)

Diagram 10(b)

Diagram 11(a)

Diagram 11 (b)

Page 77: Modul Perfect Score SBP Fizik SPM 2012

77

X A-Plus Physics Module 2012

X A-PLUS 2012

No. Situation

Q12

Diagram 12 shows a guitar. It is observed that if one of the guitar strings is plucked with bigger

displacement, the sound heard is louder.

Diagram 12

Q13

Diagram 13(a) and 13(b) show 2 identical light bulbs when the light bulbs are connected to a 6 V of

power supply. It is observed that the light bulbs light up at different brightness.

Diagram 13(a) Diagram 13(b)

Q14

Diagram 14(a) shows a girl is ironing her school uniform. After the iron is switched on for a while, there

are still wrinkles on the uniform.

Diagram 14b) shows that the wrinkles are gone when the temperature control knob as shown in figure

14(c) on the iron is turned.

Diagram 14(a) Diagram 14(b)

Diagram 14(c)

Page 78: Modul Perfect Score SBP Fizik SPM 2012

78

X A-Plus Physics Module 2012

X A-PLUS 2012

No. Situation

Q15

Diagram 15 (a) and Diagram 15(b) show two electric bells. It is observed that when the number of dry

cell used is changed, , the hammer in Diagram 15(a) strikes the gong faster compared to the hammer

in Diagram 15(b).

END OF MODULE

“Recipe for success:

Study while others are sleeping;

Work while others are loafing;

Prepare while others are playing;

and......

Dream while others are wishing...”

William A.Ward

We wish all of you

“The Very Best of Luck in Your SPM 2012

May God be with you always and give you peace of mind”

From: SBP Physics Teachers, September 2012