Nokia Asha 501 Rm-899 Rm-900 Rm-902 Service Manual 12 v10

Check the repair policy before

performing any mechanical repair on Service Level

1&2!

Service Manual for L1 and L2

Nokia Asha 501Nokia Asha 501 Dual SIMRM-899, RM-900 (Single SIM)RM-902 (Dual SIM)

Key featuresTotally new Asha Platform OS Fastlane with Swipe Motion Social and always connected 3.0" QVGA display Capacitive touch panel

Version 1.0

Exploded view Disassembly steps Assembly hints

Service devices Product controls and interfaces Solder components

Service concept

2013 Nokia | Nokia Internal Use only | All Rights Reserved.

More More More

More More More

More

Service Manual Level 1 and 2

Nokia Asha 501, Nokia Asha 501 Dual SIMRM-899 RM-900 (Single SIM), RM-902 (Dual SIM)Version 1.0

Exploded view

A-COVERI0001

TOUCH PANELI0002

EARPIECEI0003

CAMERAI0005

TOUCH IC GASKETI0006

DISPLAYI0013

DC JACKI0017

D-COVERI0018

B-COVERI0022

BACK KEYI0004

LIGHT SWAP PWBI0007

BB SHIELDING LIDI0008

FEM SHIELDING LIDI0009

WLAN SHIELDING LIDI0010

LCD CONDUCTIVE ADHESIVEI0011

TYPE LABEL I0012

IHF SPEAKERI0014

SPEAKER GASKETI0015

SPEAKER MESHI0016

ANTENNA MODULEI0019

RELEASE BUTTONI0020

SCREW TORX+SIZE 6 RF 1.6 x 5.0I0021

A-COVER AND TOUCH ASSEMBLY(I0001 - I0003)1

D-COVER ASSEMBLY(I0014 - I0018)3

LIGHT SWAP PACKAGE(I0005 - I0012)2

v1.0 Only availableas assemblyNot reuseableafter removal

Repair/swaponly in level 3




Disassembly steps

1) For disassembling you need the Nokia Standard toolkit version 2. You will also need a DC plug and thecamera removal tool SS-276.

Disassembly instructions are made with dual SIM variant.

2) Protect the A-COVER with protective film.

3) To detach the B-COVER press the RELEASE BUTTON and then pull the B-COVER with fingers.

4) Remove the B-COVER.

5) Use the finger notch to pull out and remove the battery.

6) Unscrew the four Torx+ size 6 screws in the order shown. Do not use them again.

7) Start releasing the A-COVER from the bottom end of the device. Insert the SRT-6 between the A-COVER and D-COVER and release the two clips holding the A-COVER.

NOTE: SRT-6 must be inserted vertically to avoid damages in covers.

8) Continue to release the A-COVER by inserting the SRT-6 into the gap between the A-COVER and D-COVER on the memory card side of the device.


9) Pull the D-cover to direction shown to release the shown clips.

Pay attention not to damage the A-COVER.

10) Release the top corner using the SRT-6 in the same way.


11) To release the top end insert the SRT-6 into to the gap between USB and D-COVER.

Be careful not to damage the USB connector.

12) Lift the D-COVER upwards to release the clip next to the USB.

Pay attention not to damage the covers or the USB connector.

13) Lift the D-COVER as shown.

14) Remove the D-COVER.

15) Use the dental tool to lever out the IHF SPEAKER.

Be careful not to injure yourself with the sharp end of the dental tool.

16) Use tweezers to remove the IHF SPEAKER.

17) Use the dental tool to detach the SPEAKER GASKET.

18) Use tweezers to remove the SPEAKER GASKET. Do not use it again. Discard it.

19) Use a DC plug to lift up and remove the DC JACK.

20) Insert the SRT-6 between the ANTENNA and D-COVER. Release the ANTENNA by pushing it as shown.

21) Remove the ANTENNA.

NOTE: The adhesive tapes are reusable and should stay on the D-COVER. If the adhesive tapes remain onthe ANTENNA, peel them off and place onto the D-COVER.

22) Use the SRT-6 to lever out the RELEASE BUTTON.

23) Use tweezers to remove the RELEASE BUTTON.

NOTE: Once the RELEASE BUTTON is removed the SPEAKER MESH has to be renewed also.

24) Use the dental tool to detach the SPEAKER MESH.

25) Remove the SPEAKER MESH with tweezers. Do not reuse it.

26) Disconnect the DISPLAY connector with the SS-93.

Be careful not to damage the connector or any components nearby.

27) Lever up the ENGINE BOARD with the SS-93 from the shown place.

Be careful not to damage any components nearby.

28) Release the shown clip with the SS-93.

Be careful not to damage any components nearby.

29) Lift up the ENGINE BOARD.

30) Protect the DISPLAY with protective film.

31) Protect also the other side of the A-COVER window.

32) Use SS-93 to carefully lift up the DISPLAY.

33) Separate the DISPLAY.

34) Use the dental tool to detach the TOUCH IC GASKET.

Pay attention not to make any scratches to the ENGINE BOARD.

35) Remove the TOUCH IC GASKET with tweezers. Do not use it again. Discard it.

36) Start removing the two LCD CONDUCTIVE ADHESIVE by detaching one corner with SS-93.

37) Use tweesers to peel off the adhesive. The LCD CONDUCTIVE ADHESIVE is not reusable.

38) Use the camera removal tool SS-276 to detach the CAMERA.

39) Release the EARPIECE with the dental tool.

Be careful not to damage the flex next to the EARPIECE.

40) Remove the EARPIECE with tweezers. Do not use it again. Discard it.

41) Detach the BACK KEY by pushing it with fingers. Remove it with tweezers.

42) The Nokia Asha 501 disassembly procedure is complete.

-END OF DISASSEMBLY-


Service Manual Level 1 and 2Nokia Asha 501, Nokia Asha 501 Dual SIMRM-899 RM-900 (Single SIM), RM-902 (Dual SIM)Version 1.0

Assembly hints

1) Place the IHF SPEAKER into the D-COVER. Make sure the IHF SPEAKER is aligned correctly. The pins should point towards the cavity with arrow on it.

2) When placing the RELEASE BUTTON make sure it is aligned correctly. Use the D-COVER hole as a reference. Put the RELEASE BUTTON to its place and press it until you hear the snap sound.

3) Place the shown side of the ANTENNA first into the D-COVER.

4) Fasten the ANTENNA by pressing it as shown.

5) Place the DISPLAY on the A-COVER ASSEMBLY. The driver part of the DISPLAY should be aligned with thewider gasket on A-COVER ASSEMBLY.

6) Make sure the DISPLAY is fitted to its place and press the edges of the DISPLAY slightly to activate the adhesive.

7) When placing the ENGINE BOARD make sure it is aligned correctly.

8) Place the shown side of the ENGINE BOARD first into the A-COVER ASSEMBLY.

9) Press the ENGINE BOARD carefully with fingers and check that the clips on both sides are secured.

10) Use the SS-93 to carefully fasten the B2B connector.

11) Fasten the four TORX+ size 6 screws to the torque of 14 Ncm.

-END OF ASSEMBLY HINTS-



Service devices

CA-101 Service cable AC-11 Travel charger

AC-8C & CA-190CD for China

BL-4U Battery

SS-276 Camera removal tool Nokia Standard Toolkit (v2)

For more information, refer to the Service Bulletin (SB-011) on Nokia Online. Supplier or

manufacturer contacts for tool re-order can be found in Recommended service equipment

document on Nokia Online.




Product controls and interfaces

4

5

7

3

1

6

8

9

10

11

1213

10 Volume/Zoom keys

9 Camera lens

8 Microphone

7 Back key

6 Touch screen

5 Earpiece

4 Headset connector (3.5mm)

2 Proximity sensor

3 Micro-USB connector

1 Charger connector

11 Power/lock key

12 Back cover release button

13 Antenna area

2

v1.0




Solder components

X7401

X7402 X7403F3300

F2200

X1001 J7402

J7400

G2250S1000 S1001 S1002

S1004

RF antenna spring

RF antenna GND spring

B2B connector

Power/lock switch

Backupbattery

Volume/zoom - switch

Volume/zoom + switch

GNDSpring

Backkey

GNDSpring

GNDSpring

Chargerfuse

USBfuse

TOP

BOTTOM

2013 Nokia | Confidential | All Rights Reserved.



Service concept

Flashing concept

Transceiver

Service software

CA-101

Care Dummy Batterywith power supplyvia Nokia chargeror product specific battery



Version history

Version Date Description

1.0 27.05.2013 First published version


www.s-manuals.com
http://www.s-manuals.comfront.pdfNokia Asha 501 RM-899_900_902 exploded view v1.0Nokia Asha 501 RM-899_900_902 disassembly steps v1.0Local DiskNokia Asha 501 RM-899 RM-900 RM-902 Service Manual L1L2 for Nokia CareNokia Asha 501 RM-899_900_902 assembly hints v1.0Nokia Asha 501 RM-899_900_902 service devices v1.0Nokia Asha 501 RM-899_900_902 PCI v1.0Nokia Asha 501 RM-899_900_902 solder components v1.0Nokia Asha 501 RM-899_900_902 service concept v1.0versionhistory

Nokia Asha 501 Rm-899 Rm-900 Rm-902 Service Manual 12 v10

Documents

Transcript of Nokia Asha 501 Rm-899 Rm-900 Rm-902 Service Manual 12 v10