pengkabelan
-
Upload
api-19713349 -
Category
Documents
-
view
578 -
download
3
Transcript of pengkabelan
DIT 503 NETWORKINGPRACTICAL 3: CABLING
©Copyright Reserved 2003 174
Praktikal 3
Pengkabelan(Minggu 6)
Practical 3
Cabling (Week 6)
DIT 503 NETWORKINGPRACTICAL 3: CABLING
©Copyright Reserved 2003
Objektif
Pada akhir bab ini, pelajar dapat
Mempelajari kaedah pemasangan dan penyelenggaraan kabel rangkaian.
Pengetahuan mengenai pemasangan pewayaran rangkaian SOHO.
Mengetahui dan mempelajari kaedah pemasangan pengkabelan menggunakan kabel twisted
pair dan kabel coaxial.
Objectives
At the end of this chapter, student should be able to:
Learn the method of installation and maintenance for a network cable.
Get knowledge about SOHO network wiring installation method.
Know and learn the method of cable installation using twisted pair cable and coaxial
cable.
175
DIT 503 NETWORKINGPRACTICAL 3: CABLING
©Copyright Reserved 2003
6.1 PEMASANGAN DAN PENYELENGGARAAN KABEL RANGKAIAN
Pengkabelan rangkaian, bukan hanya bergantung kepada jenis kabel, dan cara
pemasangan turut diutamakan.
Pemasangan kabel yang betul harus merangkumi perkara berikut:
a) Connectors dan kabel yang sesuai untuk jenis rangkaian tertentu, termasuk
dokumentasi komponen yang dipilih dan digunakan.
b) Label kepada keseluruhan bahagian rangkaian termasuk dinding, kabel, laluan port
panel, laluan kabel dan juga port hub.
c) Gambaran keseluruhan bangunan menunjukkan lokasi dan susun atur
pengkabelan.
d) Laporan yang menunjukkan semua kabel yang dipasang beroperasi dengan baik
menggunakan peranti pengesan rangkaian khas.
e) Untuk rangkaian jenis bus, pastikan pengguna tidak menyentuh kabel coaxial
kerana kegagalan satu kabel tersebut akan memberi kesan kepada kegagalan
nod yang lain.
6.1 NETWORK CABLE INSTALLATIONS AND MAINTENANCE.
Network cabling, depends on the type of cable and the method of installation.
The correct cable installation has to cover:
a) Connectors and suitable cable for a specific network, including the selected
component documentation that will be used.
b) Label to the entire network component, including the wall, cable, panel port path,
cable port path, and also port hub.
c) The entire picture of the building shows the location and arrangement of cabling.
d) The report shows all cables attached are operating smoothly, using a special
device to detect the network.
e) For a bus network, ensure that the users do not touch the coaxial cable, because
the malfunctioning of at least one cable will affect other nodes.
176
DIT 503 NETWORKINGPRACTICAL 3: CABLING
©Copyright Reserved 2003
6.1.1 Pemilihan Kontraktor Kabel
Apabila membina rangkaian, memilih kontraktor kabel terbaik adalah sangat penting.
Beri perhatian kepada beberapa perkara berikut:
a) Bagaimana kontraktor membuat dokumen terhadap rekabentuk kabel? Apakah
piawaian yang digunakannya dan adakah ia menepati piawaian yang
dikehendaki?
b) Adakah kontraktor akan menyediakan gambaran keseluruhan pengkabelan dalam
bangunan?
c) Bagaimana kontraktor memasang kabel untuk mengelak gangguan elektrikal ke
atas sumber pada siling dan juga lantai?
d) Adakah kontraktor mencadangkan penyelesaian kepada gabungan pewayaran
telekomunikasi (telecom wiring) dan pewayaran data (data wiring)?
Bagaimanapun, adalah lebih baik untuk mengasingkan kedua-dua pewayaran
tersebut.
e) Adakah kontraktor ada membuat pemasangan kabel lain sebagai contoh atau
gambaran?
f) Adakah kontraktor berupaya menyokong penambahan pengkabelan baru kelak?
g) Apakah peralatan yang digunakan untuk membuat pemasangan kabel?
h) Adakah kontraktor menyediakan perkhidmatan penyelesaian masalah
(troubleshooter)?
6.1.1 Choosing Cable Contractors
When building a network, it is important to choose the best cable contractor.
Need to consider the following matter:
a)How to make a document of cable design? What are the standards used and does it fulfil
the required standard?
b)Will the contractor offer the complete picture of a cable installation in a building?
c)How does the contractor install cable to prevent light distortion towards resources to
ceiling and also the floor?
d)Doe the contractor suggest a solution to the combination of telecom wiring and data
wiring? However, it is better to separate both wirings.
e) Does the contractor install other cable or show a picture as an example to his
clients?
f) Does the contractor capable of supporting the upgrading or the addition of new
cablings in the future?
g) What is the equipment used to install a cable?
h) Does the contractor offer solutions and troubleshooting?
177
DIT 503 NETWORKINGPRACTICAL 3: CABLING
©Copyright Reserved 2003
6.1.2 Penyelesaian Kepada Masalah Kabel
Masalah kabel agak sukar untuk dikesan dan dibaikpulih.
Kebanyakannya memberi kesan kepada bandwidth rangkaian pada node yang terlibat.
Untuk memastikannya adalah sukar.
Antara masalah yang melibatkan kabel adalah:
a) Prestasi rangkaian yang lembab secara mendadak, biasanya apabila satu nod yang
ketara terlibat, kesemua nod terlibat (rangkaian bintang) dan kesemua nod dalam satu
segmen lebih perlahan daripada node dalam segmen lain (rangkaian bus).
b) Kerap berlaku terputus hubungan (disconnection) daripada rangkaian.
c) Terputus hubungan secara keseluruhan ke atas hubungan pada rangkaian yang
berlaku secara berselang seli.
6.1.2 Solutions for Cable Problems
Cable problems are difficult to be detected and solved.
Most of them will affect the network bandwidth for the specific nodes. It is difficult
to pinpoint the problem.
Among the problems involving a cable are:
a) A network performance becomes slow; usually when an obvious node is involved, all
lthe nodes involved (star network), and all nodes in a segment are much slower than
nodes from other segments (bus network).
b) Disconnection always happens.
c) Total loss of connection towards network happens occasionally.
178
DIT 503 NETWORKINGPRACTICAL 3: CABLING
©Copyright Reserved 2003
RANGKAIAN BINTANG
Merupakan rangkaian yang paling mudah untuk diselenggara. Setiap nod mempunyai
kabel tersendiri yang menghala kepada hub.
Sekiranya terdapat satu nod yang gagal berfungsi, tentukan adakah masalah tersebut
datang daripada nod atau kabel. Alihkan nod tersebut di lokasi lain dan perhatikan
adakah masalah masih berlarutan.
Sekiranya ya, maka kemungkinan terdapat masalah pada komponen node tersebut
seperti NIC yang tidak berfungsi.
Sekiranya masalah adalah pada tahap normal, cuba tukar kabel daripada nod kepada
dinding. Mungkin kabel ini rosak ketika ubahsuai perabot dan komputer. Di stor wayar,
cuba hubungkan panel laluan (patch panel) daripada lokasi nod kepada port berbeza
pada hub menggunakan panel laluan (patch panel) yang berbeza. Walaupun kes ini
jarang berlaku, tetapi panel laluan (patch panel) stor wayar boleh juga rosak disebabkan
faktor masa.
Akhir sekali, tukar kabel daripada stor wayar kepada lokasi nod. Bagi kes ini, kontraktor
kabel berpengalaman dapat banyak membantu.
It is the simplest network to be maintained. Each node has its own cable directed to the
hub.
If there is a node malfunctioning, you have to decide whether the problem comes from
node or cable. Remove the node to another location and identify whether the problem
still persists.
If yes, then there must be a problem to the node component, such as a malfunctioning
NIC.
If problems happen in a normal phase, try to change cable from node to wall. Perhaps
the cable is damaged during furniture and computer maintenance or reparation. At the
wire store, try to connect patch panel from node location to a different port in the hub
by using a different patch panel. Even though these are rare cases, patch panel of wire
store can be damaged because of time factor.
Finally, change cable from wire store to node location. For this case, the cable
STAR NETWORK
179
DIT 503 NETWORKINGPRACTICAL 3: CABLING
©Copyright Reserved 2003
RANGKAIAN COAXIAL
Agak sukar untuk diselenggara kerana nod-nod berkongsi satu segmen dalam rangkaian.
Biasanya kegagalan satu segmen dalam rangkaian akan memberi kesan kepada segmen
lain dalam rangkaian.
Masalah yang biasa dihadapi adalah kehilangan hubungan kepada rangkaian ke atas
semua nod dalam segmen yang berpunca apabila terdapat individu yang mematikan
hubungan kabel kepada rangkaian untuk ubah suai pejabat contohnya.
Sekiranya tidak, maka ia akan menjadi lebih sukar untuk mengesan kegagalan kabel.
Dua cara yang biasa digunakan adalah :
a) Menggunakan pengimbas kabel coaxial
- Alat ini dipasangkan pada kabel coaxial dan ia akan memberitahu sejauh
mana kegagalan yang berlaku.
- Sambungkannya pada lokasi berbeza kabel coaxial sehingga punca
kegagalan tersebut ditemui.
b) Dapatkan lebih terminator pada rangkaian
- Putuskan hubungan (disconnect) kabel di lokasi tertentu dan sambungkan
terminator. Perhatikan sekiranya komputer pada segmen baru dan kecil tadi
boleh login ke pelayan. Pelayan harus boleh dicapai (available) dalam
segmen yang sama.
Terdapat juga masalah yang melibatkan prestasi rangkaian yang perlahan.
Namun is agak sukar untuk dikesan kerana ia jarang berlaku dan tidak mudah dikesan
dengan pengimbas kabel.
Apa yang boleh dilakukan ialah menjalankan ujian beberapa kali menggunakan terminator.
Peraturan utama dalam menyelesaikan masalah kabel memerlukan kaedah langkah demi langkah dan juga kesabaran.
180
DIT 503 NETWORKINGPRACTICAL 3: CABLING
©Copyright Reserved 2003
COAXIAL NETWORK
It is quite difficult to maintain, because nodes share a single segment in a network.
Usually the failure of a segment in a network will affect other segments in a network.
The problem faced is the loss of connection to network for all nodes in a segment, an
individual that stops cable connection in the network, in order to upgrade an office, for
example, may cause it.
If not, it will be more complicated to identify a cable’s failure.
Two methods commonly used are:
a) Using coaxial cable scanner
- This device is connected to a coaxial cable and it will tell how far a failure
is happening.
- Connect it to a different location. This device should be installed on
coaxial cable and will tell how far the failure has taken place.
b) Get more terminator to network
- Disconnect cable on specific locations and connect a terminator. Find out
whether the computer at that new and small segment can be logged into
server. The server must be available in the same segment.
There are also problems involving a weak network performance.
It is quite complicated to detect using a cable scanner, though the weakness is rare.
What can be done is by executing tests several times using the terminator.
The main regulation in solving cable problems is handling it step by step with patience.
181
DIT 503 NETWORKINGPRACTICAL 3: CABLING
©Copyright Reserved 2003
6.2 PEMASANGAN DAN PEMILIHAN RANGKAIAN SOHO
SOHO ialan singkatan bagi Small Office dan Home Office. Rangkaian SOHO merujuk
kepada persekitaran yang kecil atau pejabat di rumah yang dikelilingi oleh budaya
perniagaan. Ia juga dikenali sebagai pejabat maya (virtual office).
Rangkaian SOHO semakin popular disebabkan pelbagai faedah berikut:
a) Membolehkan perkongsian pencetak.
b) Membolehkan hubungan Internet berkelajuan tinggi dikongsi.
c) Fail (ruang storan) boleh dikongsi. Menjimatkan kerana tidak perlu membeli
perkakasan tambahan seperti tambahan RAM, cakera keras dan sebagainya.
d) Peranti salinan (backup devices) boleh dikongsi.
6.2 SELECTIONS AND INSTALLATION SOHO NETWORK
SOHO is short for Small Office and Home Office. SOHO network refers to small or
home office environment which surrounded by business culture. It also known as virtual
office.
SOHO network becomes popular because of the following advantages:
a) Enables printer sharing.
b) Enables high-speed Internet connection.
c) Sharable storage capacity. This is cost effective, as we do not have to purchase
additional equipment such as RAM, hard disk etc.
d) Sharable backup devices.
6.2.1 Pengkabelan Rangkaian SOHO
Ini merupakan bahagian yang paling sukar.
Ia bergantung kepada lokasi sebenar komputer dan bagaimana untuk melaksanakan kabel
rangkaian ke setiap lokasi komputer.
Biasanya ia dilakukan oleh individu yang berkemahiran dalam bidang rangkaian.
Kos tersebut merangkumi connectors, kabel, dan tambahan seperti wall plates dan jacks.
6.2.1 SOHO Network Cabling
This is the most complicated part.
It depends on the computer’s actual location and how to execute network cable to each of
the computer’s location.
Usually it is done by experienced individual in networking field.
The cost involves connectors, cables and additional items, such as wall plates and jacks.
182
DIT 503 NETWORKINGPRACTICAL 3: CABLING
©Copyright Reserved 2003
6.2.2 Lain-lain Pilihan Rangkaian SOHO
Bahagian paling sukar untuk memasang rangkaian SOHO adalah pewayarannya.
Tidak semua orang berkeupayaan untuk melaksanakannya kerana bukan mudah untuk
membuat lubang dan menentukan laluan kabel melalui rumah.
Dengan ini pelbagai alternatif telah dibangunkan, antaranya :
a) RANGKAIAN TALIAN TELEFON (PHONELINE NETWORKS)
Home Network Kits membolehkan wayar telefon rumah menghubungkan
komputer ke rangkaian. Antara syarikat yang menawarkan perkhidmatan ini
adalah Intel, 3Com, D-Link.
b) POWERLINE NETWORKS
Menggunakan sejenis perkakasan untuk menggunakan wayar telefon sedia ada.
Perkakasan tersebut menghantar maklumat melalui wayar dan adapter diplug
pada setiap komputer.
c) RANGKAIAN TANPA WAYAR (WIRELESS NETWORKS)
Walaupun ia agak lambat berbanding Ethernet dan rangkaian talian telefon,
namun ia mudah dari segi pemasangan. Beri perhatian kepada factor yang boleh
menghalang keupayaan rangkaian. Antara syarikat yang menawarkan
perkhidmatan ini adalah Intel dan Diamond.
6.2.2 Other SOHO Network Options
The most complicated part in a SOHO network is its wiring. Not everybody can execute
this operation, as it is very complicated to be practiced and determine cable path to
homes.
Based on these many alternatives way have developed such as:
a) PHONELINE NETWORKS
Home Network Kits enables computers to be connected to the network, by using
telephone lines. Among the companies offering this service is Intel, 3Com, D-
Link.
b) POWERLINE NETWORKS
It uses equipment to use available telephone lines. The device sends information
via wires and adapters plugged to each computer.
c) WIRELESS NETWORKS
Though it is quite slow compared to Ethernet and telephone line network, but the
installation is simpler. Consider the factors that can hamper network
performances. Among the companies offering this service are Intel and Diamond.
183
DIT 503 NETWORKINGPRACTICAL 3: CABLING
©Copyright Reserved 2003
6.3 PELAKSANAAN PENGKABELAN RANGKAIAN
PENGKABELAN TWISTED PAIR
Twisted pair (yang juga dikenali sebagai 10baseT) sangat ideal untuk rangkaian kecil,
sederhana mahupun besar yang mengkehendaki fleksibiliti dan juga kapasiti bagi
membolehkan jumlah pengguna rangkaian berkembang. Dalam rangkaian twisted pair,
komputer disusun dalam bentuk bintang. Setiap PC mempunyai kabel twisted pair yang
berhubung kepada hub.
Terdapat dalam pelbagai gred atau kategori . Kategori 5 adalah yang terbaik
dan paling kerap digunakan. Dilaksanakan dengan rangkaian 10Mbps dan juga
Fast Ethernet. Boleh didapati dalam dua kategori, straight – through atau
crossed. Tersedia dalam dua jenis, pre-made atau pengguna boleh
memotongnya sendiri. Mempunyai 8 wayar berkod warna didalamnya. Hanya
wayar 1, 2, 3 dan 6 digunakan oleh rangkaian Ethernet untuk komunikasi.
Walaupun hanya 4 wayar digunakan, kesemua lapan wayar tadi harus
dihubungkan pada kedua-dua jacks.
Kabel straight-through digunakan untuk menghubungkan komputer kepada hub.
Kabel crossed digunakan untuk menghubungkan hub kepada hub lain.
Dalam kabel straight –through, wayar 1, 2, 3 dan 6 pada satu hujung adalah
sama pada hujung yang satu lagi. Tetapi, bagi kabel crossed kedudukannya
adalah berbeza, wayar 1 akan menjadi 3 dan wayar 2 akan menjadi 6.
Twisted-pair mempunyai lebih kebolehpercayaan daripada rangkaian thin coax kerana hub tersebut berupaya membetulkan ralat data dan meningkatkan kelajuan penghantaran rangkaian. Juga dikenali sebagai uplinking, beberapa hub juga boleh dihubungkan secara bersama untuk kesan yang lebih baik.
184
DIT 503 NETWORKINGPRACTICAL 3: CABLING
©Copyright Reserved 2003
Crimping Tools
RJ 45
185
DIT 503 NETWORKINGPRACTICAL 3: CABLING
©Copyright Reserved 2003
6.3 NETWORK WIRING EXECUTION
Twisted pair, (also known as 10 base T) is very ideal for a small, medium or larger
network that will increase the amount of users in the future. In a twisted pair
network, computers are arranged in a star pattern. Each PC has a twisted pair
cable, connected to the hub.
It comes in many grades and categories. Category 5 is the best and more widely
used. It is executed in 10 Mbps network and also Fast Ethernet. It can be found in
two categories, straight through or crossed. It comes in two types, pre-made or
“Do-it-yourself”, where users can cut the wires themselves. It has 8 wires with
different colour codes in it. Only wire numbered 1,2,3, and 6 are used in an
Ethernet network for communication. Though all 8 wires are used, they have to be
connected to both jacks.
Straight-through cable is to connect the computer to the hub, while crossed cable
is used to connect the hub to another hub.
In a straight-through cable, wire number 1,2,3 and 5 at the end are similar to the
other end. On the other hand, the position of crossed cable is different, where wire
1 will be wire 3, and wire 2 will be wire 6.
Twisted-pair is more reliable than thin coax network, as the hub can correct data errors and increase speed in data a network delivery. It is also known as uplinking, where a few hubs are connected together for a better performance.
TWISTED PAIR CABLING
186
DIT 503 NETWORKINGPRACTICAL 3: CABLING
©Copyright Reserved 2003
Rajah Susunan Kabel Dalam Satu Rangkaian Mudah
Figure shows the cable arrangement in simple network
187
DIT 503 NETWORKINGPRACTICAL 3: CABLING
©Copyright Reserved 2003
Kabel Crossed- Over
Crossed-Over Cable
Kabel Straight-
Through
Straight-
Through Cable
188
DIT 503 NETWORKINGPRACTICAL 3: CABLING
©Copyright Reserved 2003
PENGKABELAN THIN COAX
Thin Coax (juga dikenali sebagai 10Base2) sangat sesuai untuk rangkaian pejabat
dengan 2 atau 3 komputer.
Sama seperti kabel yang digunakan untuk menghubungkan VCR kepada set TV,
kabel coax adalah murah dan mudah untuk dipasang.
Dalam rangkaian thin coax, yang juga dikenali sebagai backbone, komputer disusun
dalam bentuk rantaian dengan adanya permulaan dan juga akhirnya.
Setiap komputer memerlukan network card, T-connector dan sekurang-kurangnya
satu kabel coax yang masuk atau keluar. Setiap komputer pada setiap hujung
rangkaian juga memerlukan plug terminator 50-ohm.
THIN COAX CABLING
Thin Coax (also named as 10 Base2) is very suitable for office network, with 2 or 3
computers.
Similar to network connecting VCR to a TV set, coax cable is very cost effective and
simple to install.
In a thin coax network that is also known as a backbone, computer is arranged in a
string format, with a start-off and end point.
Each computer needs a network card, T-connector and at least a coax cable, that gets
in or out. Each computer at each network end point needs a terminator plug 50 ohm.
2 thin coax cable
189
DIT 503 NETWORKINGPRACTICAL 3: CABLING
©Copyright Reserved 2003
TUTORIAL 10BaseT UTP
PEMILIHAN KATEGORI PENGKABELAN
Kebanyakan kategori yang menjadi pilihan adalah Level 5 atau Category 5.
Walaupun tidak sama, namun kedua-duanya menyokong data penghantaran 100
Mbps dan keperluan fizikal kabel tersebut adalah sama, dan kedua-duanya akan
dirujuk sebagai CAT5.
Ia terdiri daripada 4 pasang wayar berpintal, jumlahnya adalah 8 wayar. Pintalan
wayar tersebut sama ada satu pintalan atau beberapa pintalan, biasanya dikenali
sebagai solid atau flex. Solid digunakan pada bahagian dinding dan siling,
manakala flex pula digunakan sebagai drop cables (kabel daripada wall plate
kepada komputer) dan patch cables (kabel daripada patch panel kepada hub).
THE SELECTION OF CABLE CATEGORIES.
The most popular category opted is Level 5 and Category 5. Even though it is not
the same, but both support data delivery 100 Mbps and the cable requirement is
similar, and both will be referred as CAT5.
It consist of 4 twisted wires, the total is 8 wires. The wire weave, consists of one
weave or more than one, usually is known as solid or flex. Solid is used at the
location of wall and ceiling, and flex is used as drop cables (cable from wall plate
to computer) and patch cable (cable from patch panel to hub)
190
DIT 503 NETWORKINGPRACTICAL 3: CABLING
©Copyright Reserved 2003
SUSUNAN PASANGAN WAYAR
Pasangan wayar mempunyai warna yang berbeza bagi memudahkan ia dikenali.
Bukan sahaja wayar itu sendiri mempunyai warna yang unik bagi memudahkan
pengenalpastian pada setiap penghujungnya, malah pasangan itu juga
mempunyai warna yang berlainan bagi memudahkan pasangan itu dikenali pada
penghujungnya.
Biasanya UTP CAT5 terdiri daripada 4 pasang, iaitu 4 wayar berwarna dan 4 lagi
wayar berbelang putih yang juga dari warna yang sama. Rujuk rajah.
Pasangan 1
Pasangan 2
Pasangan 3
Pasangan 4
Putih/BiruBiru
Putih/OrenOren
Putih/HijauHijau
Putih/CoklatCoklat
191
DIT 503 NETWORKINGPRACTICAL 3: CABLING
©Copyright Reserved 2003
THE ARRANGEMENT OF WIRE PAIRS
The wire pair has a different colour from each other for identification. Not only
the wire has a unique colour at each end, but also the pair has a different colour,
to be easily recognizable.
Usually UTP consist of 4 pairs, that is 4 coloured pairs, and 4 white striped wires.
Refer to the diagram.
Pair 1
Pair 1
Pair 3
Pair 4
White/BlueBlue
White/OrangeOrange
White/ GreenGreen
White / BrownBrown
192
DIT 503 NETWORKINGPRACTICAL 3: CABLING
©Copyright Reserved 2003
CONNECTORS
Paling biasa digunakan bersama UTP CAT5 adalah RJ45. RJ
bermakna Registered Jack dan 45 menentukan skema penomboran
pin. Connector disambungkan kepada kabel dan jack adalah peranti
di mana connector diplugkan kepadanya samaada di dalam dinding,
dalam NIC di komputer atau pada hub.
Kini kabel sedia untuk dimasukkan kepada RJ45 merujuk kepada
skema pewayaran EIA/TIA-568B RJ-45 seperti berikut:
Dua lagi pasangan wayar disambungkan seperti berikut :
Pin 1 Putih/Oren
Pasangan 2
Pin 2 Oren
Pin 3 Putih/Hijau
Pasangan 3
Pin 6 Hijau
Pin 4 Biru
Pasangan 1
Pin 5 Putih/Biru
Pin 7 Putih/Coklat
Pasangan 4
Pin 8 Coklat
RJ45
193
DIT 503 NETWORKINGPRACTICAL 3: CABLING
©Copyright Reserved 2003
RJ45 is commonly used along with UTP CAT5. RJ means Registered Jack and 45
determined the pin numbering scheme. Connector is connected to the cable and jack
is the device, for the connector to be plugged to it, whether in the wall, in NIC in
computer or hub.
Then, the cable is ready to be inserted to RJ45, referring to the wiring scheme
EIA/TIA-568B RJ-45 as below:
Two other wire pairs are connected such as these:
CONNECTORS
Pin 1 White/Orange
Pair 2
Pin 2 Oren
Pin 3 Putih/Hijau
Pair 3
Pin 6 Hijau
Pin 4 Biru
Pair 1
Pin 5 Putih/Biru
Pin 7 Putih/Coklat
Pair 4
Pin 8 Coklat RJ45
8 connections
194
DIT 503 NETWORKINGPRACTICAL 3: CABLING
©Copyright Reserved 2003
Lihat rajah di bawah.
Look at the diagram below:
Wayar-wayar disusun bagi memudahkan ia dimasukkan ke dalam plug RJ45.
Wires are arranged so it easy to insert into plug RJ45
Apabila hendak dimasukkan ke RJ45, wayar tadi harus kelihatan seperti dalam rajah.
When they are ready to be inserted into RJ45, the wires have to be as in diagram.
Perhatikan susunan wayar mengikut spesifikasi yang dinyatakan di atas. Look at the wire arrangement according to spesification which given above.
195
DIT 503 NETWORKINGPRACTICAL 3: CABLING
©Copyright Reserved 2003
KABEL CROSSOVER
Terdapat sedikit perbezaan dari segi skema pewayaran, di mana pin 1 dan 2 pada
satu penghujung disambungkan kepada pin 3 dan 6 pada penghujung satu lagi, dan
pin 3 dan 6 daripada penghujung pertama disambungkan kepada pin 1 dan 2 pada
penghujung yang satu lagi. Pin 4 & 5 dan pin 7 & 8 tidak berubah.
Kedua-dua penghujung kelihatan seperti berikut:
Penghujung biasa
Pin 2 Oren
Pin 3 Putih/Hijau
Pin 4 Biru
Pin 5 Putih/Biru
Pin 6 Hijau
Pin 5 Putih/Coklat
Pin 6 Coklat
Putih / OrenPin 1
Penghujung crossover
Pin 2 Hijau
Pin 3 Putih/Oren
Pin 4 Biru
Pin 5 Putih/Biru
Pin 6 Oren
Pin 5 Putih/Coklat
Pin 6 Coklat
Putih / HijauPin 1
196
DIT 503 NETWORKINGPRACTICAL 3: CABLING
©Copyright Reserved 2003
CROSSOVER CABLE
There is a little difference in terms of wiring scheme, where pin 1 and 2 at one end
point is connected to pin 3 and 6 at the other end point, and point 3 and 6 of the first
end point is connected to pin 1 and 2 at the other point. Pin 4 & 5 and pin 7 & 8 do
not change.
Both ends should look like these:
Normal end point
Pin 2 Orange
Pin 3 White/Green
Pin 4 Blue
Pin 5 White/Blue
Pin 6 Green
Pin 5 White/Brown
Pin 6 Brown
White/OrangePin 1
Crossover end point
Pin 2 Green
Pin 3 White/Orange
Pin 4 Blue
Pin 5 White/ Blue
Pin 6 Orange
Pin 5 White/Brown
Pin 6 Brown
White/GreenPin 1
197
DIT 503 NETWORKINGPRACTICAL 3: CABLING
©Copyright Reserved 2003
Berikut adalah susunan pin-pin bagi penghujung crossend.
These are the arrangement of pins for crossend end point.
Pin 1 Putih / HijauWhite/Green
Pasangan 2 / Pair 2
Pin 2 HijauGreen
Pin 3 Putih/ OrenWhite/Orange
Pasangan 3 / Pair 3
Pin 6 OrenOrange
Susunan bagaimana wayar akan dimasukkan kepada RJ45.
This is the arrangement how wires will be inserted into RJ45.
Apabila pasangan wayar dimasukkan ke RJ45. ia harus kelihatan seperti
di dalam rajah yang diberi.
When pair wires are inserted into RJ45, they should look llike in the
given diagram.
198
DIT 503 NETWORKINGPRACTICAL 3: CABLING
©Copyright Reserved 2003
Ringkasan Pratikal 3: Penkabelan
Penkabelan
Pemasangan dan
Penyelenggaraan Kabel
Rangkaian
Pemilihan Kabel
Kontraktor
Penyelesaian Kepada
Masalah kabelPemilihan dan
Pemasangan Rangkaian
SOHO
Penkabelan Rangkaian
SOHO
Lain-lain pilihan Rangkaian
SOHO
Tutorial 10BaseT UTP
Pemilihan kategori
Penkabelan
Susunan Pasangan Wayar
Connectors
Kabel Crossover
Pelaksanaan
Penkabelan
Rangkaian
Penkabelan Kabel
TwistedPair
Penkabelan Kabel
KoaxileSummary of Practical 3: Cabeling
Cabling
Network CableIinstallations
andMaintenance.
Choosing cable contractor
Solutions for Cable Problems
Selection and
Installations
Soho Network
SOHO Network
Cabeling
Other SOHO
Network Alternatives
Tutorial 10BaseT UTP
The selection of cable
categories.
The arrangement of wire
pairs
Connectors
Crossover Cable
Network Wiring
Execution
Twisted pair
cabling
Coaxile cabling
199
DIT 503 NETWORKINGPRACTICAL 3: CABLING
©Copyright Reserved 2003 200