An-023_Motorola MTR2000 to RM

download An-023_Motorola MTR2000 to RM

of 14

Transcript of An-023_Motorola MTR2000 to RM

  • 8/10/2019 An-023_Motorola MTR2000 to RM

    1/14

    TRIDENTMICROSYSTEMSTECHNICAL SERVICES DEPARTMENT

    Title: Motorola MTR-2000 Repeater Setup for Operation wi th Raider

    and Marauder Trunking ControllersApplication Note #: AN-023 Rev. No.: 1

    Originated By: Page 1of 14

    Managers Approval:

    Date: July 17, 2012

    Page 1 of 14

    Trident Technical Support: Phone: (828) 684-7474, Email: [email protected], Website: www.tridentms.com

    Introduction

    Using the Motorola Radio Service Software (RSS), installed on a suitablePC computer, and these instructions, the Motorola MTR2000 station can beconfigured for use with the Raider and Marauder Trunking controllers. Thissupplement supports MTR RSS revisions up to R03.02.01. Answers to specificquestions pertaining to the use of the RSS can be found in the Radio ServiceSoftware Startup Manual provided with your software.

    Setup Instructions

    1. Start the Radio Service Software (RSS) and connect the MTR2000 stationto your computer. Read the contents of the stations Codeplug.

    2. From the Station Configuration window, click on the Edit Config button andthe Station Configuration window should appear. (Figure 1 below)

    3. All marked options in the Configuration window are items that must beselected just as they are shown. Other options may or may not be selecteddepending on the exact options installed in the MTR2000 or your particular

    installation.

    4. Now click on OK to return to the Station Configuration window. The pulldown menus will become active now.

    5. Click on Personality, and click on RF Options. Compare the window thatopens up with Figure 2 and make any necessary changes in the RSS. Whendone, click OK to close the window.

    6. Click on Personality, and click on Wireline. Compare the window thatappears with that in Figure 3 and make any necessary changes in the RSS.

    Everything must appear exactly as shown. When done, click OK to close thewindow.

    7. Click on Personality, and click on TRC Commands. All eight CommandList Options should show None.When done, click OK to close the window.

  • 8/10/2019 An-023_Motorola MTR2000 to RM

    2/14

    TRIDENTMICROSYSTEMSTECHNICAL SERVICES DEPARTMENT

    Title: Motorola MTR-2000 Repeater Setup for Operation wi th Raider

    and Marauder Trunking ControllersApplication Note #: AN-023 Rev. No.: 1

    Originated By: Page 2of 14

    Managers Approval:

    Date: July 17, 2012

    Page 2 of 14

    Trident Technical Support: Phone: (828) 684-7474, Email: [email protected], Website: www.tridentms.com

    8. Next, Click on Personality, and click on Channel Information. A window,as in Figure 4, will appear. Make sure that the TX Idle frequency is the sameas the Transmit frequency. Re-enter the frequency if necessary.

    9. Now, in the upper left hand corner of the Channel Information windowunder Option, click on Audio. A window should appear as in Figure 5.Every option in this window must be checked or unchecked so that itmatches Figure 5 exactly. Alarm Tone and Call Sign are the only optionsthat may differ.

    10. Continue on to the next line, PTT, in the Option window. When you clickon this one, the window that appears should look like the one in figure 6.Make sure that you correctly select the two options indicated by the arrows.Failure to do so can cause loss of transmit data.

    11. The next item to be selected from the Option window is Encoder andDecoder. These two should both have None in the Type window asindicated by the arrows in Figures 7 and 8. Click OK to close the ChannelInformation window.

    12. Write the current profile to the station and save it to disk. As soon as youget the Station Successfully Written in the message window, proceed tothe alignment portion of these instructions.

  • 8/10/2019 An-023_Motorola MTR2000 to RM

    3/14

    TRIDENTMICROSYSTEMSTECHNICAL SERVICES DEPARTMENT

    Title: Motorola MTR-2000 Repeater Setup for Operation wi th Raider

    and Marauder Trunking ControllersApplication Note #: AN-023 Rev. No.: 1

    Originated By: Page 3of 14

    Managers Approval:

    Date: July 17, 2012

    Page 3 of 14

    Trident Technical Support: Phone: (828) 684-7474, Email: [email protected], Website: www.tridentms.com

    Alignment Procedure

    1. Make sure that all alignment procedures from the Service pull down menuhave been performed except for the TX Wireline , Discriminator and the

    Aux TX Input. These will need to be performed separately.

    2. Connect a telephone transmission test set, in the terminated mode, to theLine 1 input of J6 on the rear of the station. Set it to transmit a 1004Hz toneat20.0dBm.

    3. Click on Service in the pull down menu and select Station Alignment. Nowselect the TX Wireline button from Audio Input/Output. See figure 9.

    4. After you click TX Wireline you will get a window that looks like figure 10.With the Transmission Test Set in the generate mode, type20 in the box forthe Level of test tone and click on Save. The station will immediately autocalibrate, temporarily store the value and then return you to the Station

    Alignment window.

    5. Connect the Raider or Marauder controller to the MTR2000 station at this

    time. With the top cover removed from the controller, install jumpers W22,W26 (Remove W26 in the Marauder) and W30 if they are not alreadyinstalled.

    6. Remove the Telephone Transmission Test set and connect an Oscilloscopeto pin 1 of U1 in the controller. Connect a Service Monitor to the RX port ofthe MTR Station set in the generate mode at an RF level of approximately

    80dBm.

    7. Generate a 1KHz tone deviating at 2KHz (1KHz for narrowband operation)and click on the Discriminator button in Audio Input/Output. See figure 9.

    8. Adjust the slider, (see figure 11), to obtain a 2Vp-p signal on pin 1 of U1measured with an Oscilloscope. Click Save to return to the Station

    Alignment window of figure 9.

    9. Set the Service Monitor to Receive on the Stations transmit frequency.Move the Controllers TX Test switch, SW4-2, to the down position and adjustthe TX Data potentiometer, R57, to obtain a 2Vp-p signal of low speed data,

  • 8/10/2019 An-023_Motorola MTR2000 to RM

    4/14

    TRIDENTMICROSYSTEMSTECHNICAL SERVICES DEPARTMENT

    Title: Motorola MTR-2000 Repeater Setup for Operation wi th Raider

    and Marauder Trunking ControllersApplication Note #: AN-023 Rev. No.: 1

    Originated By: Page 4of 14

    Managers Approval:

    Date: July 17, 2012

    Page 4 of 14

    Trident Technical Support: Phone: (828) 684-7474, Email: [email protected], Website: www.tridentms.com

    measured with an Oscilloscope, at pin 8 of U2.

    10. Click on the Aux TX Input button under Transmitter, (see figure 9), andadjust the slider, as in figure 12, to obtain 1KHz deviation (800Hz for narrowband operation) of low speed data as measured by the service monitor.Click Save to temporarily save the calibration data.

    11. Now, click Save from the Station Alignment window to permanently writeall the calibration data, from the previous steps, to the codeplug. If a StationSuccessfully Aligned message appears in the Message Window, you mayproceed to the setup instructions in the controller manual to complete systemintegration.

    Figure 1

  • 8/10/2019 An-023_Motorola MTR2000 to RM

    5/14

    TRIDENTMICROSYSTEMSTECHNICAL SERVICES DEPARTMENT

    Title: Motorola MTR-2000 Repeater Setup for Operation wi th Raider

    and Marauder Trunking ControllersApplication Note #: AN-023 Rev. No.: 1

    Originated By: Page 5of 14

    Managers Approval:

    Date: July 17, 2012

    Page 5 of 14

    Trident Technical Support: Phone: (828) 684-7474, Email: [email protected], Website: www.tridentms.com

    Please note the 6 items marked on Figure1. These options must be selectedexactly as shown for the external controller to function properly. The otheroptions may be left just as they are.

    Figure 2

    The Raider and Marauder series controllers have a built in Time Out Timer (TOT)

    and CW Station ID. It is recommended that these features be disabled in theMTR2000 station and programmed into the controller.

  • 8/10/2019 An-023_Motorola MTR2000 to RM

    6/14

    TRIDENTMICROSYSTEMSTECHNICAL SERVICES DEPARTMENT

    Title: Motorola MTR-2000 Repeater Setup for Operation wi th Raider

    and Marauder Trunking ControllersApplication Note #: AN-023 Rev. No.: 1

    Originated By: Page 6of 14

    Managers Approval:

    Date: July 17, 2012

    Page 6 of 14

    Trident Technical Support: Phone: (828) 684-7474, Email: [email protected], Website: www.tridentms.com

    Figure 3

    Note about Figure 3:The options on this screen must be selected exactly asshown except for the HLGT and LLGT frequencies. If any item is overlooked,improper operation or the inability to correctly align the station for an externalcontroller will result.

  • 8/10/2019 An-023_Motorola MTR2000 to RM

    7/14

    TRIDENTMICROSYSTEMSTECHNICAL SERVICES DEPARTMENT

    Title: Motorola MTR-2000 Repeater Setup for Operation wi th Raider

    and Marauder Trunking ControllersApplication Note #: AN-023 Rev. No.: 1

    Originated By: Page 7of 14

    Managers Approval:

    Date: July 17, 2012

    Page 7 of 14

    Trident Technical Support: Phone: (828) 684-7474, Email: [email protected], Website: www.tridentms.com

    Figure 4

    Make sure that the correct Bandwidth and Deviation have been selected for yourparticular mode of operation. Also, be sure to enter your transmit frequency intothe TX Idle window. These two frequencies should match for proper LTRhandshake.

  • 8/10/2019 An-023_Motorola MTR2000 to RM

    8/14

    TRIDENTMICROSYSTEMSTECHNICAL SERVICES DEPARTMENT

    Title: Motorola MTR-2000 Repeater Setup for Operation wi th Raider

    and Marauder Trunking ControllersApplication Note #: AN-023 Rev. No.: 1

    Originated By: Page 8of 14

    Managers Approval:

    Date: July 17, 2012

    Page 8 of 14

    Trident Technical Support: Phone: (828) 684-7474, Email: [email protected], Website: www.tridentms.com

    Figure 5

    Every option on this screen must be selected exactly as shown except for CallSign and Alarm Tone. If any item is forgotten, the external controller will notoperate properly. Items of extra importance are indicated by the arrows. TheRaider and Marauder have a built in CW Station Identifier that is fullyprogrammable over a modem. It is recommended that this Identifier is used

    instead of the one built into the MTR-2000.

  • 8/10/2019 An-023_Motorola MTR2000 to RM

    9/14

    TRIDENTMICROSYSTEMSTECHNICAL SERVICES DEPARTMENT

    Title: Motorola MTR-2000 Repeater Setup for Operation wi th Raider

    and Marauder Trunking ControllersApplication Note #: AN-023 Rev. No.: 1

    Originated By: Page 9of 14

    Managers Approval:

    Date: July 17, 2012

    Page 9 of 14

    Trident Technical Support: Phone: (828) 684-7474, Email: [email protected], Website: www.tridentms.com

    Figure 6

    The options shown here must be selected in the new station being programmed.Specific items of importance are indicated by the arrows. The Raider andMarauder have a built in TOT (Time-out-timer). It is recommended that those beused instead of the PTT TOT in the MTR station.

  • 8/10/2019 An-023_Motorola MTR2000 to RM

    10/14

    TRIDENTMICROSYSTEMSTECHNICAL SERVICES DEPARTMENT

    Title: Motorola MTR-2000 Repeater Setup for Operation wi th Raider

    and Marauder Trunking ControllersApplication Note #: AN-023 Rev. No.: 1

    Originated By: Page 10of 14

    Managers Approval:

    Date: July 17, 2012

    Page 10 of 14

    Trident Technical Support: Phone: (828) 684-7474, Email: [email protected], Website: www.tridentms.com

    Figure 7

  • 8/10/2019 An-023_Motorola MTR2000 to RM

    11/14

    TRIDENTMICROSYSTEMSTECHNICAL SERVICES DEPARTMENT

    Title: Motorola MTR-2000 Repeater Setup for Operation wi th Raider

    and Marauder Trunking ControllersApplication Note #: AN-023 Rev. No.: 1

    Originated By: Page 11of 14

    Managers Approval:

    Date: July 17, 2012

    Page 11 of 14

    Trident Technical Support: Phone: (828) 684-7474, Email: [email protected], Website: www.tridentms.com

    Figure 8

  • 8/10/2019 An-023_Motorola MTR2000 to RM

    12/14

    TRIDENTMICROSYSTEMSTECHNICAL SERVICES DEPARTMENT

    Title: Motorola MTR-2000 Repeater Setup for Operation wi th Raider

    and Marauder Trunking ControllersApplication Note #: AN-023 Rev. No.: 1

    Originated By: Page 12of 14

    Managers Approval:

    Date: July 17, 2012

    Page 12 of 14

    Trident Technical Support: Phone: (828) 684-7474, Email: [email protected], Website: www.tridentms.com

    Figure 9

    Figure 10

  • 8/10/2019 An-023_Motorola MTR2000 to RM

    13/14

    TRIDENTMICROSYSTEMSTECHNICAL SERVICES DEPARTMENT

    Title: Motorola MTR-2000 Repeater Setup for Operation wi th Raider

    and Marauder Trunking ControllersApplication Note #: AN-023 Rev. No.: 1

    Originated By: Page 13of 14

    Managers Approval:

    Date: July 17, 2012

    Page 13 of 14

    Trident Technical Support: Phone: (828) 684-7474, Email: [email protected], Website: www.tridentms.com

    Using an audio signal generator that will supply a 600 ohm source impedance,generate a20dBm signal into the line 1 input of J6, enter 20 into the Test Tonewindow, and click the save button.

    Figure 11

    Adjust this slider to obtain a 2Vp-p signal as measured with an Oscopeconnected to pin 1 of U1 in the controller. The input to the station is receiving a 80dBm signal modulated with a 1KHz tone deviating at 2KHz (1KHz for 12.5KHzoperation).

  • 8/10/2019 An-023_Motorola MTR2000 to RM

    14/14

    TRIDENTMICROSYSTEMSTECHNICAL SERVICES DEPARTMENT

    Title: Motorola MTR-2000 Repeater Setup for Operation wi th Raider

    and Marauder Trunking ControllersApplication Note #: AN-023 Rev. No.: 1

    Originated By: Page 14of 14

    Managers Approval:

    Date: July 17, 2012

    Page 14 of 14

    Trident Technical Support: Phone: (828) 684-7474, Email: [email protected], Website: www.tridentms.com

    Figure 12

    Flip dipswitch SW4-2 down (test mode) on the controller and adjust TX Data potR57 to obtain a 2Vp-p signal as measured with an Oscilloscope connected to pin8 of U2 in the controller. Adjust this slider to obtain 1KHz deviation (800HZ for12.5KHz operation) of low speed data as measured with a service monitor

    receiving on the stations transmit frequency.